I have a sub receiver available.
Gary
> On Oct 21, 2015, at 2:55 PM, mcelmer1 <mcelmer1@netecin.net> wrote:
>
> I chimed in on this one a few weeks ago.
>
> Same problem since day one. I bought my used Orion 1 from Ten Tec but the Sub
> receiver never worked. A couple of trips to the factory, returned to me & it
> worked for a couple of hours then died.
>
> Resets did not fix the problem. I may tear down the front panel clean some
> pins and connectors on the board but doubt if that will fix the problem.
>
> Mike
> W8TRN
> ----- Original Message ----- From: "denton sprague" <denton@oregontrail.net>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Wednesday, October 21, 2015 12:01
> Subject: Re: [TenTec] Orion sub receiver getting no signals
>
>
> well…shoot..
> that lasted all of 1/2 hour!
> The past week or so, I has been inoperative on boot up…
> and it boots up with swishing noise that repeats itself or it seems to work
> but can’t her anything but background (processor) noise, or receive sigs are
> way down in the background.
> So for the time being it will be designated back up rig in the closet…and
> will run my omni 7 for the duration.
> I also have a chance ti purchase an unknown condition orion sub receiver
> board but not too sure want to mess with that.
> I seems to be something that is not letting the sub receiver board connect to
> the rest of the system correctly..
> I have not yet done much in the way of diagnostics…but will take some time
> this fall to pull the sub receive board and see if anything amiss…cold solder
> joints, etc, clean contacts and trace down cabling.
>
> On Oct 12, 2015, at 9:07 AM, denton sprague <denton@oregontrail.net> wrote:
>
>> a little followup..
>> sub rx was inoperable this am…booted up with sub rx on ant 1 and vfo b
>> enabled yesterday.
>>
>> after letting the rig on for about 3 hours, I rebooted the rig with sub rx
>> off on the ant and vfo buttons.
>>
>> after reboot, enabled sub rx on vfo b and ant 1 buttons. Sub rx now works
>> normally….
>>
>> On Oct 11, 2015, at 11:27 AM, denton sprague <denton@oregontrail.net> wrote:
>>
>>> thanks…apparently that was it om!!
>>> On Oct 11, 2015, at 11:13 AM, Tim Wininger <ky5rtim@gmail.com> wrote:
>>>
>>>> Need both SUB RX VFO and Ant1 SUB RX depressed.
>>>>
>>>> That's how I use this sub rcvr hr. Hope it's just that.
>>>>
>>>> GD Tim, AB4B
>>>>
>>>> On Sun, Oct 11, 2015 at 12:01 PM, denton sprague <denton@oregontrail.net>
>>>> wrote:
>>>>
>>>>>
>>>>> Hi all…my trusty Orion that came back from TT for processor board
>>>>> replacement a few months ago seems to have no receive signals…this
>>>>> happened this am when booting up the rig.
>>>>> I use ant 1 as main rx/tx as well as sub rx.
>>>>> I can hear the sub noise come up when pressing the sub rx button, but
>>>>> evidently getting no signals from the antenna.
>>>>> I have only one hf antenna.
>>>>> Did a master reset to no avail.
>>>>> loose cable maybe??
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|