Don’t overlook the mother board as well. A lot of Orion’s got repaired at Ten
Tec by replacing that rather inert board for the same reason, marginal
connectors and some soldering issues.
Gary
> On Oct 23, 2015, at 9:28 AM, Carl Moreschi <n4py3@earthlink.net> wrote:
>
> I would still bet the problem is NOT a component failure but just a bad
> connection on the cables. The rigs are computers now and cable connections
> when not gold plated are unreliable with age.
>
> Carl Moreschi N4PY
> 58 Hogwood Rd
> Louisburg, NC 27549
> www.n4py.com
>
> On 10/23/2015 9:44 AM, Gary J FollettDukes HiFi wrote:
>> I agree with anyone who says that Orion circuitry is sort of convoluted. It
>> is.
>>
>> The boards were meant to either last forever (in electronic terms) or to be
>> replaced, which is why it is generally so easy to remove them.
>>
>> There is no joy in trying to replace a 200 pins SMD square pack unless you
>> have $50,000 in specialized pick and place SMD soldering equipment. I know
>> it can be done without but think of the consequences if just ONE slolderpad
>> pulls away during the process!
>>
>> Gary
>>
>>
>>
>>> On Oct 23, 2015, at 7:22 AM, Barry N1EU<barry.n1eu@gmail.com> wrote:
>>>
>>> Ha, "simple" isn't the first word that comes to my mind when looking at the
>>> Orion audio circuit schematics. "Convoluted" would be my choice. There
>>> are four audio inputs (main rx, sub rx, mic, aux in) in digital form that
>>> get routed to four audio outputs (tx audio, auxoutL, auxoutR, auxoutMain)
>>> in analog form by two stereo CODEC chips. I just don't see a simple "audio
>>> switch". I'm not even convinced the schematics (81917_6, 81917_7) match
>>> reality - the routing on the schematics looks nutso.
>>>
>>> 73, Barry N1EU
>>>
>>> On Thu, Oct 22, 2015 at 3:40 PM, mcelmer1<mcelmer1@netecin.net> wrote:
>>>
>>>> Years ago, I recall seeing a detailed block diagram of the Orion 1 - I am
>>>> not referring to the one in the manual.
>>>>
>>>> There is a simple circuit called the "audio switch" which I suspect is the
>>>> culprit.
>>>>
>>>> However, I can not find the diagram nor can I recall on which board this
>>>> circuit was located.
>>>>
>>>> Gary, I will keep your mail/address just in case.
>>>>
>>>> Mike
>>>> W8TRN
>>>> ----- Original Message ----- From: "Gary J FollettDukes HiFi"<
>>>> dukeshifi@comcast.net>
>>>> To: "Discussion of Ten-Tec Equipment"<tentec@contesting.com>
>>>> Sent: Wednesday, October 21, 2015 18:33
>>>>
>>>> Subject: Re: [TenTec] Orion sub receiver getting no signals
>>>>
>>>>
>>>> I have a sub receiver available.
>>>>
>>>> Gary
>>>>
>>>>
>>>> On Oct 21, 2015, at 2:55 PM, mcelmer1<mcelmer1@netecin.net> wrote:
>>>>>
>>>>> I chimed in on this one a few weeks ago.
>>>>>
>>>>> Same problem since day one. I bought my used Orion 1 from Ten Tec but the
>>>>> Sub receiver never worked. A couple of trips to the factory, returned to
>>>>> me
>>>>> & it worked for a couple of hours then died.
>>>>>
>>>>> Resets did not fix the problem. I may tear down the front panel clean
>>>>> some pins and connectors on the board but doubt if that will fix the
>>>>> problem.
>>>>>
>>>>> Mike
>>>>> W8TRN
>>>>> ----- Original Message ----- From: "denton sprague"<
>>>>> denton@oregontrail.net>
>>>>> To: "Discussion of Ten-Tec Equipment"<tentec@contesting.com>
>>>>> Sent: Wednesday, October 21, 2015 12:01
>>>>> Subject: Re: [TenTec] Orion sub receiver getting no signals
>>>>>
>>>>>
>>>>> well…shoot..
>>>>> that lasted all of 1/2 hour!
>>>>> The past week or so, I has been inoperative on boot up…
>>>>> and it boots up with swishing noise that repeats itself or it seems to
>>>>> work but can’t her anything but background (processor) noise, or receive
>>>>> sigs are way down in the background.
>>>>> So for the time being it will be designated back up rig in the closet…and
>>>>> will run my omni 7 for the duration.
>>>>> I also have a chance ti purchase an unknown condition orion sub receiver
>>>>> board but not too sure want to mess with that.
>>>>> I seems to be something that is not letting the sub receiver board
>>>>> connect to the rest of the system correctly..
>>>>> I have not yet done much in the way of diagnostics…but will take some
>>>>> time this fall to pull the sub receive board and see if anything
>>>>> amiss…cold
>>>>> solder joints, etc, clean contacts and trace down cabling.
>>>>>
>>>>> On Oct 12, 2015, at 9:07 AM, denton sprague<denton@oregontrail.net>
>>>>> wrote:
>>>>>
>>>>> a little followup..
>>>>>> sub rx was inoperable this am…booted up with sub rx on ant 1 and vfo b
>>>>>> enabled yesterday.
>>>>>>
>>>>>> after letting the rig on for about 3 hours, I rebooted the rig with sub
>>>>>> rx off on the ant and vfo buttons.
>>>>>>
>>>>>> after reboot, enabled sub rx on vfo b and ant 1 buttons. Sub rx now
>>>>>> works normally….
>>>>>>
>>>>>> On Oct 11, 2015, at 11:27 AM, denton sprague<denton@oregontrail.net>
>>>>>> wrote:
>>>>>>
>>>>>> thanks…apparently that was it om!!
>>>>>>> On Oct 11, 2015, at 11:13 AM, Tim Wininger<ky5rtim@gmail.com> wrote:
>>>>>>>
>>>>>>> Need both SUB RX VFO and Ant1 SUB RX depressed.
>>>>>>>>
>>>>>>>> That's how I use this sub rcvr hr. Hope it's just that.
>>>>>>>>
>>>>>>>> GD Tim, AB4B
>>>>>>>>
>>>>>>>> On Sun, Oct 11, 2015 at 12:01 PM, denton sprague<
>>>>>>>> denton@oregontrail.net>
>>>>>>>> wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>> Hi all…my trusty Orion that came back from TT for processor board
>>>>>>>>> replacement a few months ago seems to have no receive signals…this
>>>>>>>>> happened this am when booting up the rig.
>>>>>>>>> I use ant 1 as main rx/tx as well as sub rx.
>>>>>>>>> I can hear the sub noise come up when pressing the sub rx button, but
>>>>>>>>> evidently getting no signals from the antenna.
>>>>>>>>> I have only one hf antenna.
>>>>>>>>> Did a master reset to no avail.
>>>>>>>>> loose cable maybe??
>>>>>>>>> _______________________________________________
>>>>>>>>> TenTec mailing list
>>>>>>>>> TenTec@contesting.com
>>>>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>>>>>
>>>>>>>>> _______________________________________________
>>>>>>>> TenTec mailing list
>>>>>>>> TenTec@contesting.com
>>>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>>>>
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> TenTec mailing list
>>>>>>> TenTec@contesting.com
>>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>>>
>>>>>>
>>>>>>
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>>
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|