The main receiver is the tip of the mini-phone plug, and the ring is the
sub-receiver. The barrel is ground for both. I use a Radio Shack
stereo-to-mono adapter plug with the tip connected to one phono jack and the
ring to the other. (Either R/S 274-369 or 274-883) I then split the main
one with a Y-cable, with that going to my HAL RTTY-1 tuning indicator and
also the left channel of the sound card. The ring goes to the right channel
of the sound card. I use it with MMTTY now (a HAL P38 before).
No menu is involved. See the drawing on page 4 of the manual and #14 on
page 35.
Jim N7US
----- Original Message -----
From: "Dave AA6YQ" <dbernsteinsprint@earthlink.net>
To: "'Jim McDonald'" <n7us@arrl.net>; <dhb@attbi.com>; "'wa9als'"
<wa9als@starband.net>; "'RTTY Reflector'" <rtty@contesting.com>
Sent: Tuesday, July 09, 2002 10:25 PM
Subject: RE: [RTTY] FT1000MP MkV & FSK
I only get main-RX audio there; is there a menu setting or other
configuration action I must perform to get subreceiver RX on the AF OUT
line?
73,
Dave, AA6YQ
-----Original Message-----
From: Jim McDonald [mailto:n7us@arrl.net]
Sent: Tuesday, July 09, 2002 10:18 PM
To: dhb@attbi.com; 'wa9als'; 'RTTY Reflector'
Subject: Re: [RTTY] FT1000MP MkV & FSK
Sure, the AF OUT jack. It's the same on the MP and the Mark-V.
Jim N7US
----- Original Message -----
From: "Dave AA6YQ" <dbernsteinsprint@earthlink.net>
To: "'wa9als'" <wa9als@starband.net>; "'RTTY Reflector'"
<rtty@contesting.com>
Sent: Tuesday, July 09, 2002 9:09 PM
Subject: RE: [RTTY] FT1000MP MkV & FSK
While we're on the topic of the MarkV and RTTY, has anyone found a
line-level signal that includes both main and sub audio on a backpanel
connector?
73,
Dave, AA6YQ
-----Original Message-----
From: rtty-admin@contesting.com [mailto:rtty-admin@contesting.com] On
Behalf Of wa9als
Sent: Tuesday, July 09, 2002 7:55 PM
To: RTTY Reflector
Subject: Re: [RTTY] FT1000MP MkV & FSK
> There is an internal pull-up resistor on the FSK shift line, so
> grounding and opening the shift pin should produce a shift in the
> carrier frequency (either use a Mic PTT or the MOX button to key the
> rig).
Yes, the SHIFT pin is the FSK input. Based on suggestions from the
RITTY/K6STI manual, I ran my 1000MP and later, the MARK-V with just a
1-K resistor in the line between the COM port FSK output and the RTTY
shift pin (no transistor, optoisolator etc) - worked VY FB.
I don't understand why Chen is suggesting using the Mic PTT or MOX
button instead of the RTTY connector PTT pin or just using rig control
PTT.
Another thing to note with this rig is that the PACKET (AFSK) and RTTY
(FSK) connector PTT pins are in parallel - Depending on how you make
your cables, you can save a PTT line. (You don't need separate PTT
lines for AFSK and FSK). 73
_______________________________________________
RTTY mailing list
RTTY@contesting.com http://lists.contesting.com/mailman/listinfo/rtty
_______________________________________________
RTTY mailing list
RTTY@contesting.com http://lists.contesting.com/mailman/listinfo/rtty
|