Cute remark about Gilligan's Island, I suppose, but not particularly
funny, Doug.
Not all of us build commercial towers, so the information we need
apply is considerably different in many cases than that which might
apply to commercial tower installation. The average (and even the very
rare) ham tower is no where close to that which is commercial, so I
would seriously doubt one will find anyone who has ever "levelled
their guy holes" to that of the tower itself. Commercial tower
installation and ham tower installation do have some similarities, but
ham towers are obviously seldom as high or as big and some things that
necessarily apply to commercial installations can be a bit ridiculous
for the average ham.
And, it is rather obvious I misread the question, thinking it was for
the tower base (as I stated) and not the guy anchors. That said, if
the guys here were to be even with the base, they would have to be
rather tall as the ground slopes rather abruptly. Up 1800 feet on a
hill, as I did say clearly.
Rudeness is never necessary.
Michael Goins, k5wmg
Professor, Writing
University of Texas at San Antonio
On Mon, Apr 26, 2010 at 8:52 PM, Doug Westacott <ve6pr@canada.com> wrote:
> Tom:
>
>
>
> I am not a professor of anything..I build big commercial towers for a
> living...and the odd Ham job on the side..
>
> What we are talking about here is guy radius...distance from the tower base
> to the guy anchor point...
> The manufacturer's prints are normally done for flat gound...
>
>
>
> General rule of thumb for uneven round....
>
> a. for every foot anchor is above tower base move anchor back/away from tower
> a foot
> b. for every foot anchor point below tower base move anchor in a foot....
>
>
>
>
> Maybe the professor is from Giligans Island?
>
>
> Doug
> VE6PR
>
>>------- Original Message Follows -------
>>From: "Tommy Alderman" <aldermant@windstream.net>
>>To: "'Tower and HF antenna construction topics.'"<towertalk@contesting.com>
>>Subject: Re: [TowerTalk] Digging holes for anchor rods
>>Date: Mon, 26 Apr 2010 20:28:26 -0400
>>
>>Thanks Michael!
>>
>>I'm not sure if you have unlevel ground, how you would make the top of all
>>three holes level. But no problem as I have two respected references and I
>>am not going to bother with getting the bottom of the anchor holes the same
>>level.
>>
>>Thanks to all,
>>
>>Tom - W4BQF
>>
>>
>>
>>-----Original Message-----
>>From: towertalk-bounces@contesting.com
>>[mailto:towertalk-bounces@contesting.com] On Behalf Of Michael Goins
>>Sent: Monday, April 26, 2010 8:22 PM
>>To: Tower and HF antenna construction topics.
>>Subject: Re: [TowerTalk] Digging holes for anchor rods
>>
>>No. Make sure the TOP is level and all will be fine.
>>
>>Michael Goins, k5wmg
>>Professor, Writing
>>University of Texas at San Antonio
>>
>>
>>
>>
>>
>>
>>
>>On Mon, Apr 26, 2010 at 6:32 PM, Tommy Alderman
>><aldermant@windstream.net> wrote:
>>>
>>>
>>> It has been posed to me by a local commercial construction supervisor,
>>that
>>> I use a laser leveler to make sure the bottom of the anchor rod holes are
>>at
>>> the same level. While I have great faith of this persons word (based on
>>the
>>> experience he has on the job.), I have never heard of any ham going to
>>these
>>> lengths. My tower site ground does not change drastically, possibly a foot
>>> difference from the other two holes.
>>>
>>>
>>>
>>> In you tower builders opinion, do you think this is a necessary step? Did
>>> you do it when installing your own tower?
>>>
>>>
>>>
>>> Many thanks for any input.
>>>
>>>
>>>
>>> 73,
>>>
>>>
>>>
>>> Tom - W4BQF
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>>_______________________________________________
>>
>>
>>
>>_______________________________________________
>>TowerTalk mailing list
>>TowerTalk@contesting.com
>>http://lists.contesting.com/mailman/listinfo/towertalk
>>
>>_______________________________________________
>>
>>
>>
>>_______________________________________________
>>TowerTalk mailing list
>>TowerTalk@contesting.com
>>http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|