In the cell industry there is two splices on every run. Usually 1/2" jumper
from the cabinet to the ground buss polyphasers
where it then transitions to 1 5/8". It then goes up the tower to another 5'
or 6' 1/2" jumper to the antenna.
All connectors. If you try and splice it without one, you don't have any
business using the 1/2" to begin with. IT WILL
not be correct.
73 Dave
n4zkf
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of
larryjspammenot@teleport.com
Sent: Thursday, August 28, 2008 1:15 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Splicing LDF4
I wondered if it was the money or just why else the Andrew, etc. connectors
weren't used for making a splice. I have yet to go to a ham swap meet in the
last 10 years or so (including Dayton) where I don't see lots of used 1/2"
and 7/8" Heliax connectors (used) going for $2-5 each, new ones for $5-20
each. It seems like if you're going to go to all the trouble of using good
feedline that good connectors would be used with it. Just my opinion, of
course.
-----Original Message-----
>From: "Dubovsky, George" <George.Dubovsky@andrew.com>
>Sent: Aug 28, 2008 8:28 AM
>To: "larryjspammenot@teleport.com" <larryj@teleport.com>,
>towertalk@contesting.com
>Subject: Re: [TowerTalk] Splicing LDF4
>
>If money is no object, connectors or in-line splices are a good
>solution. Above HF, perhaps the only "good" solution. In my case, I had
>a bunch of 50-60 foot lengths of 1/4" superflex, and I needed to reach
>a 160 meter vertical 250 feet away. I think 4 bux of brass tubing
>allowed me to splice 4 or 5 lengths of the 1/4" together. I put proper
>connectors on the two ends, and I ran it for 3 years laying on top of
>the ground. It got replaced with buried 1/2" aluminum hard line just
>this summer. BTW, I swept the spliced cable on an HP network analyzer,
>from 1-30 MHz, and darned if I could see any degradation in insertion
>loss. Don't recall if I looked at S11.
>
>If it's for free, it's for me...
>
>73,
>
>geo - n4ua
>
>-----Original Message-----
>From: towertalk-bounces@contesting.com
>[mailto:towertalk-bounces@contesting.com] On Behalf Of
>larryjspammenot@teleport.com
>Sent: Thursday, August 28, 2008 11:15 AM
>To: towertalk@contesting.com
>Subject: Re: [TowerTalk] Splicing LDF4
>
>I kept wondering why this wasn't suggested in the first place - I see
>it done at commercial 2-way radio tower sites all the time. Proper
>weatherproofing/waterproofing of the mating connectors being done with
>tape, Scotchkote or whatever being used, of course.
>
>Am I missing something obvious?
>
>
>-----Original Message-----
>>From: Ed Richardson <ed_richardson@shaw.ca>
>>Sent: Aug 27, 2008 5:05 PM
>>To: towertalk@contesting.com
>>Subject: Re: [TowerTalk] Splicing LDF4
>>
>>I think the best way to splice the cable length would be to use an
>>Andrew Male N on one end and a female N on the other. Provides a great
>>solid connection that can be undone if required. Connectors can often
>be
>>found at local flea markets or even on EBay for a fraction of the cost
>>of new ones.
>>
>>This way cable will last for years without maintenance.
>>
>>Good Luck!
>>
>>Ed VE4EAR
>>
>>_______________________________________________
>>
>>
>>
>>_______________________________________________
>>TowerTalk mailing list
>>TowerTalk@contesting.com
>>http://lists.contesting.com/mailman/listinfo/towertalk
>
>_______________________________________________
>
>
>
>_______________________________________________
>TowerTalk mailing list
>TowerTalk@contesting.com
>http://lists.contesting.com/mailman/listinfo/towertalk
>
>
>-----------------------------------------------------------------------
>------------------------- This message is for the designated recipient
>only and may contain privileged, proprietary, or otherwise private
>information.
>If you have received it in error, please notify the sender immediately
>and delete the original. Any unauthorized use of this email is
>prohibited.
>-----------------------------------------------------------------------
>-------------------------
>[mf2]
>
>_______________________________________________
>
>
>
>_______________________________________________
>TowerTalk mailing list
>TowerTalk@contesting.com
>http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|