Bob....So are you just sending tones in sideband mode??? If you are on USB,
and
just using the line in, that is what it sounds like.
...Dave
----- Original Message -----
From: "Robert & Linda McGraw K4TAX" <RMcGraw@Blomand.Net>
To: <tentec@contesting.com>
Sent: Sunday, May 23, 2004 4:40 PM
Subject: Re: [TenTec] computer CW my Argonaut V???
> Can't specifically say about the Argonaut V but.......... in doing high
> speed CW for meteor scatter I use a piece of software to specifically
> generate and receive such. To that end the audio INs and audio OUTs of
the
> Omni VI+ or Paragon II for that matter are connected to the respective
Line
> OUT and Line IN on the sound card. No interface required. Just good
> shielded audio cable with proper connectors. I operate the radio in USB
> under VOX control and out comes CW.
>
> I'll try it with MixW in the CW mode and see how it behaves. I'd expect it
> to work quite well at "low speed" CW. I can say that MixW seems to copy
> good machine or keyer generated CW quite well. On the other hand, a sloppy
> fist is a sloppy fist and it's just plain hard to copy.
>
> 73
> Bob, K4TAX
>
>
> ----- Original Message -----
> From: "Tommy" <aldermant@alltel.net>
> To: <tentec@contesting.com>
> Sent: Sunday, May 23, 2004 3:29 PM
> Subject: Re: [TenTec] computer CW my Argonaut V???
>
>
> > I have been using YPlog for a little over three years. YPlog gives you
the
> > option of using the sound card generated CW audio, or the parallel port.
I
> > chose to use the sound card CW generation simply because via that
method,
> > because with the CPU 'sharing' as it does in Windows, it does not
interupt
> > the generated sound. I made a simple RS audio step-up xfmr and a
> four-diode
> > bridge rectifier to drive a NPN transistor, which keys my rigs. YPlog
does
> > not decode CW. A program that does decode CW is called CWget, however
be
> > aware that very few CW decoders work well in normal rcvr background
noise,
> > at speeds much in excess of about 55 wpm, if that happens to be your
goal.
> >
> > Tom - W4BQF
> >
> > ----- Original Message -----
> > From: "Dave Edwards" <kd2e@comcast.net>
> > To: <tentec@contesting.com>
> > Sent: Sunday, May 23, 2004 9:58 AM
> > Subject: [TenTec] computer CW my Argonaut V???
> >
> >
> > I am going to fool around with the direct ins & outs to a sound card
that
> my
> > new argo comes with.
> > Can anyone suggest a program to encode and decode cw, and how it hooks
up?
> > I can see how it uses the line out for decoding cw, but how does the
> 'puter
> > key the cw?
> >
> > Thanks to anyone who is already doing this!!
> > ...Dave
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|