Yeah, I noticed that, too, but thought I'd wait to report it until Ron
complains that he has nothing left to work on!
73,
Ed - W0YK
> -----Original Message-----
> From: trlog-admin@contesting.com [mailto:trlog-admin@contesting.com]On
> Behalf Of Robert Brandon
> Sent: Thursday, December 05, 2002 11:16 AM
> To: 'TRLog Reflector'
> Subject: RE: [TRLog] Why no Ctrl-Fx keys in exchange mode?
>
>
> You're right! It's just that the instructions at the bottom of the
> screen say only:
> "Press ex function key to program <F3-F12, AltF1-AltF12, or ESCAPE to
> exit>:"
>
> This is different from the CQ instructions which way,
> "Press CQ function key to program <F1, AltF1, CtrlF1>, or ESCAPE to
> exit."
>
> -----Original Message-----
> From: J. Edward (Ed) Muns [mailto:w0yk@msn.com]
> Sent: Thursday, December 05, 2002 11:38 AM
> To: Robert Brandon; 'TRLog Reflector'
> Subject: RE: [TRLog] Why no Ctrl-Fx keys in exchange mode?
>
> Ctrl-F keys are already available in Exchange mode. It is documented in
> manual 6.63, page 140, and I use them all the time.
>
> 73,
> Ed - W0YK
>
>
> > -----Original Message-----
> > From: trlog-admin@contesting.com [mailto:trlog-admin@contesting.com]On
> > Behalf Of Robert Brandon
> > Sent: Thursday, December 05, 2002 8:58 AM
> > To: 'TRLog Reflector'
> > Subject: [TRLog] Why no Ctrl-Fx keys in exchange mode?
> >
> >
> > In CQ mode, there are three sets of programmable keys -- plain F1-F10,
> > Alt-F1-F10, and Ctrl-F1-F10. In exchange mode, however, only plain F
> > keys and Alt-F keys are available. I had in mind to set up Ctrl-F
> keys
> > for second radio fills, etc.. Would it be possible to add Ctrl-F keys
> > in exchange mode?
> >
> > Robert K5PI
> >
> > -----Original Message-----
> > From: trlog-admin@contesting.com [mailto:trlog-admin@contesting.com]
> On
> > Behalf Of Mike Gilmer, N2MG
> > Sent: Thursday, December 05, 2002 6:26 AM
> > To: U.Lautenbach@OLG-Senate-Kassel.Justiz.Hessen.de
> > Cc: TRLog Reflector
> > Subject: Re: Antwort: Re: [TRLog] Why?
> >
> > N2MG wrote:
> > > > Also, some of the CW messages (F1 and F2 in exchange) are not
> > > > accessible/editable from ALT-P - only in the cfg file. Why is
> that?
> >
> > DL2ZAZ wrote:
> > > They are accessed by Alt-P O because they can also be sent by the
> > enter
> > > key.
> >
> > OK, I do see why F1 on ALT-P E is like it is (it's "MYCALL" and should
> > be
> > setup in cfg and probably NOT changed mid-contest) Also, F2 has two
> > settings, so allowing access on that page might be ugly. However since
> > both
> > F2 choices ARE accessible via ALT-P O it should SAY this on the ALT-P
> E
> > page - there IS enough room. The way the ALT-P E page is laid out it
> > looks
> > like both F2 and F1 are only available in the cfg. I realize this can
> > be
> > "learned" but it would make it easier for new TR users.
> >
> > Mike N2MG
> >
> >
> > _______________________________________________
> > TRLog mailing list
> > TRLog@contesting.com
> > http://lists.contesting.com/mailman/listinfo/trlog
> >
> >
> > _______________________________________________
> > TRLog mailing list
> > TRLog@contesting.com
> > http://lists.contesting.com/mailman/listinfo/trlog
> >
>
>
>
> _______________________________________________
> TRLog mailing list
> TRLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/trlog
>
|