Re: [WriteLog] CW Jitters

["Joe Subich, W4TV" <lists@subich.com>]

On 2020-08-02 9:37 PM, Randy Thompson wrote:
> The examples all show screen shots so that is probably not much help
> for you.
The examples also include step by step (text) captions.  For example
(from the "microKEYER II and WriteLog Setup" document):

> 1. Click Setup| Ports ...
> 2. Select K1EL WinKey as the CW keyer type
> 3. Assign CW to the WinKey port you used in Router's
>    Ports tab
As far as I know, both WriteLog and microHAM USB Device Router use
standard screen libraries that are compatible with screen readers.

73,

   ... Joe, W4TV


On 2020-08-02 9:37 PM, Randy Thompson wrote:
> The examples all show screen shots so that is probably not much help for you.
>
> Make sure the MicroHam software specifies a port for WinKey.
>
> In Writelog, go to ports and set CW keyer type to K1EL Winkey.  Leave SO2R 
> Control set to none.
>
> Set the radio button for CW to the com port that you specified in the MicroHam 
> software.
>
> That should get you to the point that CW messages are keying things.
>
> You say it works for N1MM+ so have to figure it is something the WriteLog setup.
>
> Randy K5ZD
>
> -----Original Message-----
> From: WriteLog <writelog-bounces@contesting.com> On Behalf Of 
> rgarrett5@comcast.net
> Sent: Sunday, August 2, 2020 6:37 PM
> To: 'Robert' <woodr90@gmail.com>
> Cc: 'WriteLog Reflector' <writelog@contesting.com>
> Subject: Re: [WriteLog] CW Jitters
>
> Hello Robert  et al,
>
>   
>
> So under “CW” in the configuration section, I have 8 choices.  The only MicroHam 
> setting is for MKR which is used with SO2R.  I’m a visually impaired guy so if there is 
> another place on the screen where Microham MKII is listed, please tell me.  I certainly am not able 
> to read it.
>
>   
>
> The only other setting for CW is the five choices I assume for LPT and com 
> ports.  Any input appreciated.  73, Bob K3UL
>
>   
>
> From: Robert <woodr90@gmail.com>
> Sent: Sunday, August 2, 2020 4:43 PM
> To: rgarrett5@comcast.net
> Subject: RE: [WriteLog] CW Jitters
>
>   
>
> FWIW
>
>   
>
> I’m hooking up winkey2 this month
>
>   
>
> have used the PC generated CW in past – normally it works great but think RF 
> got computer few times on that transistor interface
>
> and it would jitter & quit.  then reboot…
>
>   
>
>   
>
> check the writelog settings, if you’re got Microham 2 set in CW window, then 
> it’s a mystery to me
>
> My only experience with Microham was at Carl’s rental, the P40YL side had MicroHam, 
> Most – including me, unhooked it and used USB to RS232 or whatever instead then hooked 
> back up as was.
>
>   
>
> 73 W5AJ
>
>   
>
> Robert
>
> Midland, Texas
>
>   
>
> From: rgarrett5@comcast.net <mailto:rgarrett5@comcast.net>  
> [mailto:rgarrett5@comcast.net]
> Sent: Sunday, August 02, 2020 1:24 PM
> To: 'Robert' <woodr90@gmail.com <mailto:woodr90@gmail.com> >
> Subject: RE: [WriteLog] CW Jitters
>
>   
>
> Hello Robert,
>
>   
>
> MicroHam MKII.
>
>   
>
> I just want to be sure I don’t have some incorrect setting where I believe I’m using 
> the WINKEYER in the MicroHam MKII when I’m not and actually using PC generated CW..
>
>   
>
> From: Robert <woodr90@gmail.com <mailto:woodr90@gmail.com> >
> Sent: Sunday, August 2, 2020 2:04 PM
> To: Bob Garrett <rgarrett5@comcast.net <mailto:rgarrett5@comcast.net> >
> Subject: Re: [WriteLog] CW Jitters
>
>   
>
> How are you interfacing from writelog/computer to Rig on CW?
>
>   
>
> PC generate?
>
> Winkeyer?
>
> Etc?
>
>   
>
> W5AJ
>
>   
>
> On Sun, Aug 2, 2020, 7:10 AM <rgarrett5@comcast.net <mailto:rgarrett5@comcast.net> 
> > wrote:
>
> Greetings,
>
> I've had an ongoing problem using WriteLog with CW breaking up or having some 
> delays, speeding up or slowing down, mostly speeding up in the middle of a 
> message.  Any thoughts as to why this behavior?  73, Bob K3UL

_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/