Lee,
I think this one got stuck in the Bit Bucket so I'm re sending it.
It was the predecessor to the one that started with "PS"
-----Original Message-----
From: k8mp <k8mp@aol.com>
To: lee <lee@wa3fiy.com>; tentec <tentec@contesting.com>
Sent: Sun, Mar 4, 2018 11:18 am
Subject: Re: Re[2]: [TenTec] I surrender
Aha! So it does work!
What rig did you choose from the Radio Set-up? The two generic-sounding Icom
choices talk to the Omni VI for freq and mode but they don't key it.
Carl suggested that there may not be a keying command, per se, so maybe they're
toggling something else in FLDigi and MMTTY.
I'm looking at the FLDigi rig control set up and that one has Omni VI in its
list, so that one was a no-brainer. (How lucky for me).
I noticed there's a check box that says "PTT via HamLib command" (HamLib is
what they call their list of rigs that they are pre-set-up for control)
That box is checked and it suggests to me that PTT is done via a radio command.
Regarding the PC to radio connections, I'm using a serial port for rig control
and the Line-in/out from the PC directly to the Audio out/in on the back of the
rig.
I'm looking at MMTTY now. It also has Omni VI Plus in its radio list, so it was
also a no brainer.
It's interesting to note that MMTTY also shows the RX and TX command syntax.
( \$FEFExxE01601FD\w10 for TX )
In my and Winmor TNC Setup, I just picked the PC's sound card device names from
the drop-downs.
In the Radio set-up, I tried both of the generic Icom choices, (Changed the rig
address to 04 to talk to the Omni)
Those both talk to the Omni, except for making it xmit.
What are your Winmor settings Lee?
Thanks, Joe
-----Original Message-----
From: Lee <lee@wa3fiy.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Cc: k8mp <k8mp@aol.com>; tentec <tentec@contesting.com>
Sent: Sun, Mar 4, 2018 9:24 am
Subject: Re[2]: [TenTec] I surrender
Joe,
The Omni VI works fine with Winlink Winmor. I have one here that I have
used many times.
I assume MMTTY and fldigi are being used with the Omni. If so, then we
know the hardware interface works so it is only a configuration issue
with Winlink. What do you use for an interface between your computer
and the Omni? In Winlink there are two setup screens that need
attention, "WINMOR TNC setup" and "Radio Setup". TNC setup selects
the sound card interface and Radio Setup selects radio control if used
(yours appears to be working fine) and PPT control.
Can you look at the MMTTY or fldigi setup parameters to get an idea of
what works?
73,
-Lee-
WA3FIY
Sounds like the PTT line to the Omni is not getting triggered.
>> _______________________________________________
>> TenTec mailing list
>> <a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a> <<a
>>href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
>> <a href="http://lists.contesting.com/mailman/listinfo/tentec";
>>target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>_______________________________________________
>TenTec mailing list
>TenTec@contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|