Joe,
The Omni VI works fine with Winlink Winmor. I have one here that I have
used many times.
I assume MMTTY and fldigi are being used with the Omni. If so, then we
know the hardware interface works so it is only a configuration issue
with Winlink. What do you use for an interface between your computer
and the Omni? In Winlink there are two setup screens that need
attention, "WINMOR TNC setup" and "Radio Setup". TNC setup selects
the sound card interface and Radio Setup selects radio control if used
(yours appears to be working fine) and PPT control.
Can you look at the MMTTY or fldigi setup parameters to get an idea of
what works?
73,
-Lee-
WA3FIY
Sounds like the PTT line to the Omni is not getting triggered.
------ Original Message ------
From: "Joe Papworth via TenTec" <tentec@contesting.com>
To: n4py3@earthlink.net
Cc: k8mp@aol.com; tentec@contesting.com
Sent: 3/4/2018 8:12:21 AM
Subject: Re: [TenTec] I surrender
Hmmm...
I run MMTTY and FLFigi on that same PC over the same connection and
they key the Omni VI Plus fine.
Those work but WinLink/Winmor does not, so it's gotta be something in
the program or a setting in it.
Later, Joe, K8MP
Sent from AOL Mobile Mail
-----Original Message-----
From: Carl Moreschi <n4py3@earthlink.net>
To: k8mp <k8mp@aol.com>
Cc: tentec <tentec@contesting.com>
Sent: Sun, Mar 4, 2018 06:54 AM
Subject: Re: [TenTec] I surrender
I don't think the Omni VI implemented that command.
Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
<a href="http://www.n4py.com"; target="_blank">www.n4py.com</a>
On 3/4/2018 12:06 AM, <a href="mailto:k8mp@aol.com";>k8mp@aol.com</a>
wrote:
They're talkin' Carl. The rig accepts the mode and QRG commands from
the
PC but apparently it doesn't accept the command to xmit.
Sent from AOL Mobile Mail
-----Original Message-----
From: Carl Moreschi <<a
href="mailto:n4py3@earthlink.net";>n4py3@earthlink.net</a>>
To: Discussion of Ten-Tec Equipment <<a
href="mailto:tentec@contesting.com";>tentec@contesting.com</a>>
Sent: Sat, Mar 3, 2018 11:12 PM
Subject: Re: [TenTec] I surrender
There's 3 things that have to match.
Baud rate (probably 1200 but might not be )
CIV address (should be 04 )
Correct comport number.
If all those match it will work.
Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
<a href="http://www.n4py.com"; target="_blank">www.n4py.com</a> <<a
href="http://www.n4py.com"; target="_blank">http://www.n4py.com</a>>
On 3/3/2018 10:32 PM, Joe Papworth via TenTec wrote:
> Gents,
>
> <div>I threw in the towel on making WinLink and Winmor work with
my
Omni VI Plus. I have WinLink working over our local Mesh network and
I
was hoping get it working on HF but no dice.
>
> Thank you Carl, Rod, Greg, and others who weighed in.
>
> Joe, K8MP
>
> Sent from AOL Mobile Mail</div>
> _______________________________________________
> TenTec mailing list
> <a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
<<a
href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
> <a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>
_______________________________________________
TenTec mailing list
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a> <<a
href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
<a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|