Thanks Greg! The link is now fixed. It's actually the PAT12B board.
73, Barry N1EU
On Mon, Dec 26, 2016 at 9:02 PM, Greg S via TenTec <tentec@contesting.com>
wrote:
> Thanks, Barry. The link on the wiki page points to wrong website for me. I
> understand it should go to the PAT50 i.f. Interface board designed for
> 12Mhz. Great, another project for the Omni VI+ when it gets on the
> bench! Merry Christmas to the TT family.Greg, KC8HXO
>
> From: Barry N1EU <barry.n1eu@gmail.com>
> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> Sent: Sunday, December 25, 2016 1:22 PM
> Subject: Re: [TenTec] Panadapter with 9MHz i.f.
>
> I posted a Web page with all the panadapter info including photos of the
> buffer amp mod in the Omni 6+: http://omni6.wikidot.com/panadapt
>
>
> 73 & Happy Holidays,
> Barry N1EU
>
> On Sat, Dec 24, 2016 at 7:38 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:
>
> > Thanks Steve. I'm finding that I can use 9.000MHz for i.f., cw offset is
> > equal to (minus) sidetone frequency, USB offset is -3000Hz and LSB offset
> > is zero.
> >
> > Yes, I'm using OmniRig to interface to the Omni 6+.
> >
> > HDSDR software has a neat "Mirror RF Spectrum in general" checkbox that
> > makes the spectrum move correctly with the Omni 6/SDRPlay combo. Back
> when
> > I used an Orion/LP-Pan, I never saw the flipped spectrum issue.
> >
> >
> >
> > 73, Barry N1EU
> >
> > On Sat, Dec 24, 2016 at 7:21 PM, Steve Ellington <steven4lq@gmail.com>
> > wrote:
> >
> >> Barry
> >> I fiddled with this on a Corsair II. The offset for it was 750 Hz for cw
> >> but on the O6 it would depend on your sidetone frequency setting. I
> would
> >> guess 1500 Hz for SSB +/-. I lost interest because it tuned backwards.
> >> IOW.... tuning up the band caused the signals to move down. It's an (IF)
> >> thing:*)
> >> I would think OmniRig would be needed to interface the rig to SDR-C but
> I
> >> used HDSDR. It can operate OmniRig which in turn operates most any rig
> via
> >> serial port.
> >> Let us know how it goes.
> >> Steve N4LQ
> >>
> >> On Sat, Dec 24, 2016 at 1:48 PM, Barry N1EU <barry.n1eu@gmail.com>
> wrote:
> >>
> >> > Can anybody please provide the correct freq settings to use with
> >> panadapter
> >> > software being driven off the 9MHz i.f. output:
> >> >
> >> > IF OUTPUT 9.???.??? MHz
> >> > Offsets CW ??? Hz
> >> > LSB ??? Hz
> >> > USB ??? Hz
> >> >
> >> > FWIW, I'm driving an SDRPlay RSP1 off my Omni 6+ 9MHz i.f. through a
> >> > Clifton Labs Z10000B buffer amp. I'm using SDR Console v3 software.
> >> This
> >> > looks like it's going to be a very cool setup. I am fully documenting
> >> the
> >> > install.
> >> >
> >> > Thanks & 73,
> >> > Barry N1EU
> >> > _______________________________________________
> >> > TenTec mailing list
> >> > TenTec@contesting.com
> >> > http://lists.contesting.com/mailman/listinfo/tentec
> >> >
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >
> >
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|