TenTec
[Top] [All Lists]

Re: [TenTec] Tentec 302 Remote tuning knob/encoder for Omni 5, 6 and 6+

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Tentec 302 Remote tuning knob/encoder for Omni 5, 6 and 6+
From: Barry N1EU <barry.n1eu@gmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 28 Mar 2015 15:45:26 +0000
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I had no luck after opening the 302. I'm emailing Ten-Tec and asking if
they can provide a 302R schematic.

73, Barry N1EU

On Sat, Mar 28, 2015 at 12:43 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:

> No, it's not working Harri and my wiring looks correct.
>
> I guess I need to open up the 302 and double check the pin numbers.  The
> 302 works fine with my Orion,
>
> 73, Barry N1EU
>
> On Sat, Mar 28, 2015 at 12:11 PM, Harri Sillanpää <harsil@phnet.fi> wrote:
>
>> Hello Barry.
>>
>> Sorry i made mistake, this is measure in today:
>>
>> All is measure in cable side
>>
>> 8-pin DIN male IN CABLE   to 25DB male:
>>
>> 8 --> 16
>> 2 --> 14
>> 7 --> 8
>> 3 --> 6
>>
>> Here is link picture, where i found 8-pin DIN connectors number:
>> left side picture CABLE SIDE:
>>
>> http://freespace.virgin.net/tom.baldwin/pinout-8din.html
>>
>> I hope it works now, if not ask,
>>
>> sorry my mistake.
>>
>> 73 Harri OH3PC
>>
>> 12:42, Barry N1EU kirjoitti:
>>
>> > Hi Harri,
>> >
>> > I wired up my 302 remote to the DB25 on the Omni 6+ and it is not
>> tuning.
>> > Can you confirm that the pin 1, 6, 2, and 8 connections that you gave me
>> > for the DIN plug from the 302 are numbered the same as this diagram?
>> >
>> > [image: Image result for 8-pin din connector]
>> >
>> > When I connect an oscilloscope to the 4 connections, I see +5V and
>> ground
>> > but I don't see any encoder pulses on the other two pins
>> >
>> > Is there a schematic anywhere for the 302?
>> >
>> > Thanks & 73,
>> > Barry N1EU
>> >
>> > On Sun, Mar 8, 2015 at 10:00 AM, Harri Sillanpää <harsil@phnet.fi>
>> wrote:
>> >
>> > > Here is how i made it.
>> > >
>> > > NOTE ! ONLY KNOB WORKS, NOT KEYBOARD!
>> > >
>> > > CONNECT 8-PIN din Male to 25 pin DB-connector:
>> > >
>> > > 8-pin DIN connector   25-pin DB-connector
>> > >
>> > > pin 1 to pin 6
>> > > pin 6 to pin 8
>> > > pin 2 to pin 14
>> > > pin 8 to pin 16
>> > >
>> > > Only 4-wires need.
>> > >
>> > > i can send to pictures, if someone wants.
>> > >
>> > > 73 Harri OH3PC
>> > >
>> > >
>> > > --
>> > > Harri Sillanpaa
>> > > Varpusenkatu 12
>> > > FI-15610 LAHTI
>> > > FINLAND
>> > > 040/7599172
>> > >
>> > >
>> > >
>> > >
>> > > _______________________________________________
>> > > TenTec mailing list
>> > > TenTec@contesting.com
>> > > http://lists.contesting.com/mailman/listinfo/tentec
>> > >
>> > _______________________________________________
>> > TenTec mailing list
>> > TenTec@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/tentec
>> >
>>
>>
>> --
>> Harri Sillanpaa
>> Varpusenkatu 12
>> FI-15610 LAHTI
>> FINLAND
>> 040/7599172
>>
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>