TenTec
[Top] [All Lists]

Re: [TenTec] Tentec 302 Remote tuning knob/encoder for Omni 5, 6 and 6+

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Tentec 302 Remote tuning knob/encoder for Omni 5, 6 and 6+
From: Barry N1EU <barry.n1eu@gmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 28 Mar 2015 12:43:44 +0000
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
No, it's not working Harri and my wiring looks correct.

I guess I need to open up the 302 and double check the pin numbers.  The
302 works fine with my Orion,

73, Barry N1EU

On Sat, Mar 28, 2015 at 12:11 PM, Harri Sillanpää <harsil@phnet.fi> wrote:

> Hello Barry.
>
> Sorry i made mistake, this is measure in today:
>
> All is measure in cable side
>
> 8-pin DIN male IN CABLE   to 25DB male:
>
> 8 --> 16
> 2 --> 14
> 7 --> 8
> 3 --> 6
>
> Here is link picture, where i found 8-pin DIN connectors number:
> left side picture CABLE SIDE:
>
> http://freespace.virgin.net/tom.baldwin/pinout-8din.html
>
> I hope it works now, if not ask,
>
> sorry my mistake.
>
> 73 Harri OH3PC
>
> 12:42, Barry N1EU kirjoitti:
>
> > Hi Harri,
> >
> > I wired up my 302 remote to the DB25 on the Omni 6+ and it is not tuning.
> > Can you confirm that the pin 1, 6, 2, and 8 connections that you gave me
> > for the DIN plug from the 302 are numbered the same as this diagram?
> >
> > [image: Image result for 8-pin din connector]
> >
> > When I connect an oscilloscope to the 4 connections, I see +5V and ground
> > but I don't see any encoder pulses on the other two pins
> >
> > Is there a schematic anywhere for the 302?
> >
> > Thanks & 73,
> > Barry N1EU
> >
> > On Sun, Mar 8, 2015 at 10:00 AM, Harri Sillanpää <harsil@phnet.fi>
> wrote:
> >
> > > Here is how i made it.
> > >
> > > NOTE ! ONLY KNOB WORKS, NOT KEYBOARD!
> > >
> > > CONNECT 8-PIN din Male to 25 pin DB-connector:
> > >
> > > 8-pin DIN connector   25-pin DB-connector
> > >
> > > pin 1 to pin 6
> > > pin 6 to pin 8
> > > pin 2 to pin 14
> > > pin 8 to pin 16
> > >
> > > Only 4-wires need.
> > >
> > > i can send to pictures, if someone wants.
> > >
> > > 73 Harri OH3PC
> > >
> > >
> > > --
> > > Harri Sillanpaa
> > > Varpusenkatu 12
> > > FI-15610 LAHTI
> > > FINLAND
> > > 040/7599172
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
>
>
> --
> Harri Sillanpaa
> Varpusenkatu 12
> FI-15610 LAHTI
> FINLAND
> 040/7599172
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>