I ended up adding the 9MHz i.f. output to the Orion main rx per the VE7TK
mod instructions and the results have been quite good.
With the RX366, there were two +15dB humps in my passband approx +/-25KHz
from center freq. Also, the rx signal levels seemed attenuated/compressed
- for example, a signal that was 30dB above the noise on the receiver might
show up as only 15dB above noise on the if output. But as I said, it might
be completely different on the Eagle.
73/Happy Holidays,
Barry N1EU
On Tue, Dec 23, 2014 at 5:10 AM, Rick - DJ0IP / NJ0IP <Rick@dj0ip.de> wrote:
> GM Barry,
>
> Did your route involve the R366 at all, or was it an entirely different
> solution?
> It seems many people have reported successfully using this tap on the
> Eagle.
> Perhaps they had/have the problem that you flagged but just didn't notice
> it.
>
> Can you explain please what the result is when the passband is not flat.
> Tnx.
>
> Merry Christmas!
>
> 73 - Rick, DJ0IP
> (Nr. Frankfurt am Main)
>
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Barry
> N1EU
> Sent: Tuesday, December 23, 2014 10:24 AM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Eagle 9MHz tap questions.
>
> The 9MHz i.f.tap as supplied by the factory may or may not give
> satisfactory
> results driving a panadapter. My experience with the similar
> RX366 subreceiver were not entirely satisfactory - the passband was not
> flat
> and had some anomalies. I ended up going another route. Your experience
> might be different and if you try, please report back with your results..
>
> 73, Barry N1EU
>
> On Tue, Dec 23, 2014 at 1:18 AM, Drago <osijek.osijek@os.t-com.hr> wrote:
>
> >
> >
> > -----Izvorna poruka----- From: Rick - DJ0IP / NJ0IP Sent: Tuesday,
> > December 23, 2014 5:32 AM To: 'Discussion of Ten-Tec Equipment' Subject:
> > Re: [TenTec] Eagle 9MHz tap questions.
> > I was wanting to add a pan-adapter.
> > I may have to replace a board in order to do that.
> > My unit does not have the TMP jack with the 9 MHz out.
> >
> > Also I have to find a way to run the signal out the back.
> > I already have two spare RCA Phono jacks in use for the pre-selector.
> >
> > 73 - Rick, DJ0IP
> > (Nr. Frankfurt am Main)
> >
> > -----Original Message-----
> > From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
> > Richards
> > Sent: Tuesday, December 23, 2014 2:49 AM
> > To: Discussion of Ten-Tec Equipment
> > Subject: Re: [TenTec] Eagle 9MHz tap questions.
> >
> > Are you going to add a panadapter ?
> >
> > ================== K8JHR ==================
> >
> >
> > On 12/22/2014 2:46 PM, Rick - DJ0IP / NJ0IP wrote:
> >
> >> Is it just a tap, like perhaps a Y-connection, or does it also have a
> >>
> > buffer stage?
> >
> >> Unfortunately my Eagle fell out of the nest before that feature was
> >> added
> >>
> > to the radio.
> >
> >> ____________________________________________
> >>
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|