MIKE, I AM COMPLAINING.
NOW YOU ARE AWARE OF ONE! :-)
By the way, the Orion originally shipped with no hang time.
Scott and I had a hefty debate whether QSK was the only thing needed and
eventually I convinced Jack that there were plenty of people who do not want
QSK and plenty more whose amp can't cope with it, so he had Gary contact me
to understand the problem and the requirements. Gary changed the software
and the post dit delay (hang) was implemented.
Unfortunately the Eagle didn't get this hang delay either.
Therefore an external box is required to add it when running older amps in
CW mode.
73 - Rick, DJ0IP
(Nr. Frankfurt am Main)
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Mike
Schatzberg
Sent: Wednesday, September 24, 2014 9:08 PM
To: k9yc@arrl.net; Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] din connector, etc.
The Orion II delays RF for 15 ms after closure of the amplifier contacts.
This applies to Ant1 and Ant2 as well.
The amplifier hang time is adjustable for either Ant1 or Ant2 but the 15 ms
delay is not adjustable and is applied in SSB and CW.
The hang time keeps the amp from dropping out between characters if you
wish. You can adjust it to hear your own echo coming back with very fast
QSK.
The 15 ms guarantees no hot switching of course with all QSK systems.
No one has complained about a limitation in top speed that I am aware of.
73,
Mike
W2AJI
Sent from my iPhone
> On Sep 24, 2014, at 2:38 PM, Jim Brown <k9yc@audiosystemsgroup.com> wrote:
>
> Understood, Rick. But 17msec pretty much rules out QSK above about 18
WPM. A strange design compromise for Ten Tec. :) Frankly, I'm both
surprised and disappointed to see Ten Tec go for the lowest common
denominator -- they never used to do that. For my money, amps with open
frame relays are for ragchewing on SSB, not serious operating.
>
> FWIW, delay in the K3 is continuously adjustable, and I think it is in the
FT1000MP too. I sold mine around 2008 to buy my K3s. The TS850, which I also
owned, is fixed at about 8 msec. The K2 is 8 msec.
>
> Also FWIW, K6XX published a simple "speed up" circuit for T/R relays
> quite a few years ago, which he credits to K1KP.
> http://www.k6xx.com/radio/fastrely.pdf
>
> 73, Jim K9YC
>
>> On Wed,9/24/2014 2:08 AM, Rick - DJ0IP / NJ0IP wrote:
>> Jim, I just sent an email explaining exactly how the Eagle works.
>> The Orion and Omni VII both have 15mS initial delay. The Eagle is 17.
>>
>> "17mS" is relative.
>>
>> For amps with vacuum relays or PIN Diode switching, it is long.
>> For amps with open-frame relays it is too short.
>>
>> I have never seen an open-frame relay that can switch in all cases,
>> no matter what, in less than 20ms.
>> The open-frame relay used in all Ameritron amps can occasionally take
>> as long as 22mS - even though Ameritron advertises 15mS.
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|