For those early radios, TT offered an "AirPax" fast acting magnetic circuit
breaker for mobile users or others who didn't use the TT current limited
supply. These are available from the usual vendors, although they now seem
to have become part of Sensata Technologies.
Regards, Joel Hallas, W1ZR
Westport, CT
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Rick -
DJ0IP / NJ0IP
Sent: Wednesday, August 28, 2013 1:26 PM
To: 'Discussion of Ten-Tec Equipment'
Subject: Re: [TenTec] Using Non-TT Supply
I have a hunch your assumption is correct, Paul.
73
Rick, DJ0IP
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Paul
Kraemer
Sent: Wednesday, August 28, 2013 4:32 PM
To: 'Discussion of Ten-Tec Equipment'
Subject: Re: [TenTec] Using Non-TT Supply
If that is an issue then use the VS-35M model with front panel adjustable
current limit that can be set from 1.5 amp up to max of the supply. The
voltage is also adjustable from front panel.
I haven't taken each apart but I wager the only difference between the
VS-35M and the RS-35M is the adjustments brought out to a knob Paul K0UYA
--------------------------------------------------
From: "Rick - DJ0IP / NJ0IP" <Rick@DJ0IP.de>
Sent: Tuesday, August 27, 2013 11:28 PM
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] Using Non-TT Supply
> Paul,
>
> The over current protection in your RSM 35 is not the same as the over
> current protection used in the Ten-Tec power supplies. The RSM 35's
> over current protection is to protect the power supply itself. The
> Ten-Tec power supplies had their over current protection set to
> exactly the maximum permissible current for the transceiver's finals,
> and that helped protect the final transistors. Ten-Tec used this
> method for almost 20 years. I think the Omni VI was the first
> transceiver which did not rely on the power supply for the extra
> protection.
>
> There is nothing special about the Ten-Tec circuit, other than the
> point at which it shuts down. Older models ceased at 18A, later ones
> at 20A (as the
> new transceivers required more current). Any good power supply with an
> adjustable current parameter would also work like the Ten-Tec power
> supplies. However how often do you see someone using a P.S. with an
> adjustable current limit?
>
> Bottom line, your suggestion is only good for the newer transceivers.
> Don't
> use it with the older Omni's or Corsairs.
>
> 73
> Rick, DJ0IP
>
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Paul
> Kraemer
> Sent: Tuesday, August 27, 2013 11:46 PM
> To: tentec@contesting.com
> Subject: Re: [TenTec] Using Non-TT Supply
>
> John
> I use Astron RSM 35 with all my solid state radios including OMNI VI
> Very good supply with overvoltage and over current protection Paul
>
>
> --------------------------------------------------
> From: "John Farler" <k4avx1@windstream.net>
> Sent: Tuesday, August 27, 2013 3:21 PM
> To: <tentec@contesting.com>
> Subject: [TenTec] Using Non-TT Supply
>
>> My supply for the TT Omni V or VI has problems. When I tune up, even
>> to a dummy load, the pilots in the radio dim and output is not where
>> it should be on 40 meters and up.
>> Current is less than 20 A, but I haven't checked the voltage drop yet.
>>
>> My question is can I use a non-TT supply with the Omni VI safely? I
>> remember someone on the list saying TT stopped using the original
>> type of power supply like the one with the old Triton which kicks of
>> at a certain current, but I can't remember which radio it is that
>> doesn't depend on the "circuit breaker" type of protection.
>>
>> I have several non-TT supplies that will provide the current and more
>> - is it safe to use them with the Omni V, VI??
>>
>> I'm guessing the filters in the power supply have gone bad...actually
>> it has 3 in parallel.
>> How can I check for one bad one, or can I?
>>
>> Thanks, and I hope my post is not too confusing....
>>
>> John, K4AVX
>> k4avx1@windstream.net
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|