Yes! Agree -- I could handle an "IQ" ouput in order to run Spectrum Analysis
software on a pc.
----- Original Message -----
From: "Carl Moreschi" <n4py2@earthlink.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Wednesday, May 18, 2011 2:04 PM
Subject: Re: [TenTec] Orion III
> My Orion III would be an Orion II with the addition of a sub-receiver
> that is equal to the main receiver, a 9 mhz IF out jack, and receive
> antenna out/back in loop connections so you could add devices such as a
> noise cancelor in series with the receiver. It would also have 6 meters.
>
> Carl Moreschi N4PY
> 121 Little Bell Dr.
> Hays, NC 28635
> www.n4py.com
>
> On 5/18/2011 1:50 PM, Frank Kirschner wrote:
>> Listen to the NR on the FTdx-5000. It can pull a signal out of the noise
>> and make an unreadable signal readable, and a noisy signal armchair copy.
>> This works on SSB as well as CW. I don't know what algorithm they're
>> using, but it really works.
>>
>> 73,
>> Frank
>> KF6E
>> ----- Original Message -----
>> From: Carl Moreschi
>> Sent: 05/14/11 11:37 AM
>> To: Discussion of Ten-Tec Equipment
>> Subject: Re: [TenTec] Orion III
>>
>> The NR you are talking about does not exist on any radio. Still to this
>> day I have never seen an NR that truely helps with copy. They might make
>> things quieter but copy is always best under difficult conditions with NR
>> off. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com
>> On 5/14/2011 11:12 AM, Tony Lelieveld wrote:> Hi all,> > I agree. I'd
>> go with an external panadapter. Why are people rumbling about> an Orion
>> III? Let's get the O-II finalized first. I am still waiting for> an
>> upgrade that will improve the NR part of the rig. One that, when you>
>> activate it, will truly reduce the noise WITHOUT altering the audio
>> quality> of the voice you're receiving.> > On some signals it seems to
>> work okay but mostly it distorts the audio and> acts erratically and I
>> am running ver. 2.044A. Different settings of the> AGC threshold and
>> manual AGC level do not seem to make much difference.> > 73, Tony
>> VE3DWI> > > ----- Original Message -----> From: "Bar
> ry N1EU"<
>> barry.n1eu@gmail.com> > To: "Discussion of Ten-Tec
>> Equipment"<tentec@contesting.com> > Sent: Thursday, May 12, 2011 12:29
>> PM> Subject: Re: [TenTec] O3 wish list> > >> Well said and totally
>> agree Paul. Limited engineering resources can>> be put to much better
>> use. If the rig mfr provides I.F. output,>> they've done their job.>
>> _______________________________________________> TenTec mailing list>
>> TenTec@contesting.com>
>> http://lists.contesting.com/mailman/listinfo/tentec>
>> _______________________________________________ TenTec mailing list
>> TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|