Have you read this yet? This might help you.
http://www.wispnotes.com/articles/14
Dan
On Wed, 2003-07-02 at 18:27, wesley allison wrote:
> Ok, I think I have narrowed this down to my AP-1000. I have a router hook to
> the internet with a live IP, this router is using NAT to give me 192.168.0.X
> private address with 192.168.0.1 being the gateway address. I have my
> AP-1000 hooked to this router and a few clients spread around the house. I
> have set the clients up and they can ping all the way back to the AP-1000
> but not out to the internet. I do not have NAT turned on at any of the
> client stations or the AP-1000 and everyone is set in route mode not bridge.
> I am stuck and I am sure it is the one big tree in my face that is the
> reason I am unable to see the forest. I am sure if someone as example of a
> similar setup I will see my mistake.
>
> wes
> ----- Original Message -----
> From: "Darko Delic" <darko@tradal.net>
> To: "Karlnet Mailing List" <karlnet@WISPNotes.com>
> Sent: Wednesday, July 02, 2003 2:02 AM
> Subject: Re: [Karlnet] routing question
>
>
> > Hello,
> >
> > First of all, what do you mean by "to route out to the internet to hold
> > down on broadcast" ???
> >
> > Are you using NAT on AP-1000 since in your example you stated that you
> > use private IPs which are not routeable outside your network ?
> >
> > It would be good if you can send output of ip routes from configurator.
> >
> >
> > On Tue, 2003-07-01 at 18:27, wesley allison wrote:
> > > I just received all my equipment and Karlnet software and I am in the
> > > process of getting things squared away. I have setup my AP-1000 as a
> base
> > > station and my RG-1000 as a satellite. I have decided to route from my
> cpe
> > > to the base station and out to the internet to hold down on broadcast
> > > traffic. I am having a problem getting to the internet from my CPE. I
> can
> > > ping all the way back to the base station, but I can't get to the
> internet.
> > > I do have my Base setup as a bridge at this point but I have tried it
> both
> > > ways and I seem to get blocked at the base station. The way I would like
> to
> > > do it is at the CPE I run DHCP on the Ethernet connection and route that
> > > traffic to the wireless interface, then from that wireless interface to
> the
> > > base station wireless interface, then to the base station Ethernet
> interface
> > > and out on the internet and back. So I was checking to see if anybody
> had
> > > any suggestions. "quick note everything works fine in bridge mode all
> the
> > > way from the cpe to the internet, so the equipment is working fine."
> > >
> > > example
> > > 10.10.10.1 -----> 192.168.1.10 RG-1000 hooked to client computer
> > > cpe Ethernet cpe wireless
> > >
> > > 192.168.1.10 ------> 192.168.1.5 RG-1000 connected to AP-1000 base
> > > station
> > > cpe wireless base wireless
> > >
> > > 192.168.1.5--------> 192.168.1.1 AP-1000 base station connected to
> > > internet connection
> > > base wireless internet
> > >
> > > Thanks
> > >
> > > wes
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > --
> > Darko Delic <darko@tradal.net>
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
|