Software has been updated. It will only allow one cluster to receive DX
spots. It can be set using the SPOTCLUSTER command, otherwise, it is the
1st cluster the user is connected to.
73, Gerry
On Mon, Nov 10, 2008 at 7:04 PM, Gerry Hull <gerry@w1ve.com> wrote:
> Correct.. use this to connect skimmer and ONE internet cluster. Don't use
> it for two clusters.
>
>
> 73, Gerry
>
> On Mon, Nov 10, 2008 at 5:00 PM, David Robbins K1TTT <k1ttt@arrl.net>
> wrote:
>
> > DANGER! DO NOT send the same outgoing spot to multiple nodes, this can
> > result in your spots showing up multiple times around the world and get
> > sysops annoyed at you.
> >
> >
> > David Robbins K1TTT
> > e-mail: mailto:k1ttt@arrl.net
> > web: http://www.k1ttt.net
> > AR-Cluster node: 145.69MHz or telnet://dxc.k1ttt.net
> >
> >
> > > -----Original Message-----
> > > From: cq-contest-bounces@contesting.com [mailto:cq-contest-
> > > bounces@contesting.com] On Behalf Of Gerry Hull
> > > Sent: Monday, November 10, 2008 21:40
> > > To: CQ-Contest; Tom - N1MM; yccc@yccc.org
> > > Subject: [CQ-Contest] ClusterJoin... Mix your Telnet Cluster Spots and
> > > CWSkimmer spots into same application.
> > >
> > > http://www.w1ve.com/ClusterJoin.zip
> > >
> > > This is free software.
> > >
> > > What it is: It's a TCP Daemon that listens for connections on a port
> > (23
> > > is the default, Telnet) and connects to other servers, and mixes the
> > > content.
> > >
> > > Once you've connected, you can then connect to as many telnet spot
> > sources
> > > as you would like.
> > >
> > > I dreamed this up as a way to connect CW Skimmer and an external
> cluster
> > > to
> > > N1MM at the same time.... Therefore, get the spots from Skimmer along
> > > with
> > > everything from the net.
> > >
> > >
> > > Example:
> > >
> > > ------ K1TTT.NET (for example)
> > >
> /
> > > N1MM setup to connect to ClusterJoin (locahost)
> > > \
> > >
> > > ------- CW SKIMMER on localhost:7300
> > >
> > >
> > > There is no limit to the number of clients that can connect to
> > > ClusterJoin,
> > > as well as no limits on the number of clusters you can connect to.
> > >
> > > I think, perhaps, it's silly to connect more than one real-world
> cluster,
> > > unless you want to...
> > >
> > > All traffic sent to ClusterJoin goes to all connected telnet sessions.
> > > you must log in to each session.
> > >
> > > You'lll get instructions when you log in.
> > >
> > > ClusterJoin.exe is a 14Kb file, and is a Windows Console application.
> > > Just leave it running and minimize.
> > > It is a .Net application and requires the .Net Framework 2.0 be
> installed
> > > on
> > > your system. You can get that from Microsoft's site if you don't have
> > it.
> > >
> > > No install -- just extract ClusterJoin.exe from the Zip file and go.
> > >
> > > I'm not on the CWSkimmer reflector, so some one please pass it on.
> > >
> > > Enjoy!
> > >
> > > 73, Gerrry W1VE
> > > _______________________________________________
> > > CQ-Contest mailing list
> > > CQ-Contest@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/cq-contest
> >
> >
> >
> >
> _______________________________________________
> YCCC Reflector mailto:yccc@contesting.com
> Yankee Clipper Contest Club http://www.yccc.org
> Reflector Info: http://lists.contesting.com/mailman/listinfo/yccc
>
>
--
73,
Gerry Hull, W1VE/VE1RM
w1ve@yccc.org
sip: gerry@voip.w1ve.com
aim: w1ve
ym: w1ve
msn: w1ve@hotmail.com
Post and See Scores in Realtime - Try www.getscores.org
_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest
|