Set your radio mic gain with the TT-715 in the OUT position. The TT-715 has
an output level setting on the back. With the PROC Gain set to about seven
o'clock or just about 6 dB of clipping you should set the output level so
the radio's peak RF output is the same when the TT-715 is IN as when it is
OUT. Once you have that output level set correctly, you can change the pass
band and proc gain. There's plenty of gain in the TT-715 making it easy to
over drive the radio. Amplified, rising response, and hi-output microphones
should be used cautiously with the TT-715.
I find using a separate receiver to make recordings for playback is the best
way for me to make TT-715 Passband and level adjustments with various
microphones.
73 ES DX,
Gary -- AB9M
-----Original Message-----
From: Bry Carling
Sent: Tuesday, February 18, 2014 8:12 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] F.S. New Ten Tec 715 RF Processor
OK thanks - interesting. Who knows then. Must be something magic about those
Tentec
microphones and processors.
It could be that the signal level is vastly different from what is expected
by the processor. Or it
could be that the signal level coming out of the processor is suitable for a
Tentec radio but
NOT suitable for the Drake radios etc. It certainly sounds to me like
something was
overdriving somewhere. You may have had some levels set wrong. Generally you
want to run
the mic gain in the radio a little higher, and reduce the drive level going
into it. With the
processor it wil lbe very important to use the correct drive level for your
mic signal going into
it, and have it be at the expected impedance. Any overdriving at any stage
will produce some
rough sounding audio.
73 de AF4K, Bry
On 18 Feb 2014 at 17:35, Joe W2KJ wrote:
Howdy Bry:
The 444D can be switched between HI and LO impedance...so that's not
the problem...I also used a 600 ohm headset with similar
results....it's not a mike impedance problem.
73, Joe W2KJ
On Feb 18, 2014, at 4:20 PM, Brian Carling wrote:
> It sounds like you might possibly have had an impedance mismatch.
Most attend tech equipment and other modern equipment uses low
impedance microphones, around 600 ohms.
>
> If you use microphones like the Shure 444 and other high impedance
microphones, they can be loaded down and sound pretty terrible.
>
> Best regards - Bry Carling
>
>
>
>> On Feb 18, 2014, at 4:06 PM, Joe W2KJ <w2kj@bellsouth.net>
wrote:
>>
>> Howdy Gang:
>>
>> Last year I bought a model 715 RF Speech Processor from Ten Tec
and played with it for several months with my Drake gear but
couldn't get the audio to sound good.
>>
>> A couple of weeks ago I called Ten Tec to let them know that the
715 wasn't working well with my Drake gear so they told me to send
the unit back to them for a look-see.
>>
>> I received a brand new unit last week and still had the same
problem of poor audio with my Drake gear...using a 444D mike
provided excellent audio with the Drake stuff but not through the
715.
>>
>> Since the 30 day return policy was no longer in effect I couldn't
get a refund from Ten Tec.
>>
>> I was told by a Ten Tec rep that a similar complaint was received
from an amateur not getting good audio from his Collins gear with
the 715.
>>
>> I guess the 715 is designed to work with newer gear...I have also
heard that the 715 was designed to work FB with more "restricted
audio" microphones...not sure exactly what that means though.
>>
>> The 715 gets excellent reviews on eHam Product Reviews..all using
newer equipment not vintage gear.
>>
>> In any event, I appreciate the support I received from Ten Tec
and have decided to sell the 715 since I can't use it with my Drake
gear.
>>
>> I offer the unit for sale...it is brand new.....will ship for
$175.00.
>>
>> It comes with a cable designed for Ten Tec equipment.
>>
>>
>> Digital picture on request.
>>
>> Many thanks.
>>
>> 73, Joe W2KJ
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|