Hello Barry ,Mark,
For Info.
I had a word with Tentec and the suggestion for two L/S one on the main and
the other on the 2nd RX and to be able to use headphones (although
headphones OR main L/S on the main) is to use a stero splitter plugged into
the Headphone socket on the front ,and feed both L/S from there. Ive tried
it and the audio gain seems to be OK but Im not sure about the matching -as
I dont have a circuit.
I think the new 2nd receiver when it is available will give more audio
gain, and its got a pre amp.... so the RF gain control wont have to be so
high.
Thanks all
Dave G3RXP
----- Original Message -----
From: "Dave G3RXP" <g3rxp@btinternet.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Wednesday, November 09, 2011 1:55 PM
Subject: Re: [TenTec] Orion 2 query L/S on 2nd receiver.
Hi Guys,
As soon as you connect headphones to the front socket the loudspeakers
inside and external speaker is disabled so it doesnt matter how you
configure the audio controls I cannot get them to all work at the same
time.
I agree on the RF control, and this is always the way I have run a RX
whatever the type -but the trouble is that the S meter doesnt work.
Dave
----- Original Message -----
From: "Mark van Wijk" <pa5mw@home.nl>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Cc: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Wednesday, November 09, 2011 11:09 AM
Subject: Re: [TenTec] Orion 2 query L/S on 2nd receiver.
One more thing.......
Never use any outboard (DSP) processor for the audio. The greatest asset
of the ORION is its ability of a wonderfull recovered audio presentation.
Use your RF Gain, never set it above 90. Ever. Not even on 10/12mtrs.
So, .....actually two :)
73, Mark,PA5MW
On 9 nov. 2011, at 11:29, Dave G3RXP <g3rxp@btinternet.com> wrote:
Hi Barry and Mark thanks for the info - I think the internal L/S is
disabled
when the external L/S is plugged in, the same with headphones - but Ill
check those suggestions again.
Just thinking about it I have my headphones connected to the back exp
L/S
via an external DSB audio filter so that may be the problem.
Thanks Dave
----- Original Message -----
From: "Barry N1EU" <barry.n1eu@gmail.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Wednesday, November 09, 2011 9:28 AM
Subject: Re: [TenTec] Orion 2 query L/S on 2nd receiver.
On Wed, Nov 9, 2011 at 9:18 AM, Dave G3RXP <g3rxp@btinternet.com>
wrote:
I would like to monitor the 2nd RX by loudspeaker and use the
headphones
for the main RX and wondered what is the best method to do this. I
could
use the line output socket at the back but I may have missed an easy
option?
Why not use the EXT SPKR output on the rear panel (or just the Orion's
internal speaker) with Audio configured as Left/Right=Main and
Spkr=Sub?
Barry N1EU
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|