Sounds like something is out of whack on the timing of your serial
connection. The default for the Orion is 57,600 baud, No Parity, 8 Data
bits, 1 Stop bit. This should be the setting in your computer device
manager for the COM port you're using.
Ron N6IE
www.N6IE.com
----- Original Message -----
From: "John" <brazos@rochester.rr.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Friday, February 27, 2009 3:22 PM
Subject: Re: [TenTec] 041 firmware rev
I have been updating now for over an hour and have only got to line 1050
out
of 10,000 lines should I be patient or just scrap the attempt ?
----- Original Message -----
From: "John" <brazos@rochester.rr.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Friday, February 27, 2009 6:11 PM
Subject: Re: [TenTec] 041 firmware rev
When downloading the new firm ware should the radios screen show a
counter
of the lines being downloaded ( am in Flash Update Mode ) my radio does
not
show any running totals John
----- Original Message -----
From: "Jim M." <jmiller1706@cfl.rr.com>
To: "'Ron Castro'" <ronc@sonic.net>; "'Discussion of Ten-Tec Equipment'"
<tentec@contesting.com>
Sent: Friday, February 27, 2009 5:37 PM
Subject: Re: [TenTec] 041 firmware rev
Well I downloaded it off the web a few times and apparently got a copy
that
works ok now. I wonder if TT puts some sort of checksum or other
integrity
check on the file? If you are getting some weird behavior you might try
another download off the web until something changes.
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]
On Behalf Of Ron Castro
Sent: Friday, February 27, 2009 4:49 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] 041 firmware rev
http://radio.tentec.com/downloads/transceivers/566
Ron N6IE
www.N6IE.com
----- Original Message -----
From: "Jim M." <jmiller1706@cfl.rr.com>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Friday, February 27, 2009 1:41 PM
Subject: Re: [TenTec] 041 firmware rev
On the phone with TT, he suggested various reset sequences but the load
won't work. Said file might have been corrupted and to download it
again,
still no luck. Now reverting back to previous version, hope I didn't
crash
my radio. Could someone give me that download site again just to be
sure?
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]
On Behalf Of kc9cdt@aol.com
Sent: Friday, February 27, 2009 4:13 PM
To: tentec@contesting.com
Subject: Re: [TenTec] 041 firmware rev
Make sure stop on error is ON,
Lee
-----Original Message-----
From: Jim M. <jmiller1706@cfl.rr.com>
To: 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
Sent: Fri, 27 Feb 2009 4:04 pm
Subject: Re: [TenTec] 041 firmware rev
Well not having a lot of luck here. Somehow crashed the O2 first time
trying with an old serial card in the PC, and it was very slow. Got a
USB
to serial converter and it flashed in about 5 mins this time but
nothing
in
the radio works, no knob, no buttons, and the display reads all zeros
frequency. Am trying the flash again. Stay tuned. So far I am
underwhelmed.
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]
On Behalf Of Peter Frenning [OZ1PIF]
Sent: Friday, February 27, 2009 3:57 PM
To: Ron Castro; Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] 041 firmware rev
Ron Castro skrev:
I have noticed that the levels between the AF and RF AGC's are quite
different. The AF is very low compared to RF.
Ron Castro
Chief Technical Officer
Results Radio, LLC
N6IE
www.N6IE.com
Same here, but doesn't seem to have detrimental effects other than you
have to twist up the AF encoder...
--
Vy 73 de OZ1PIF/5Q2M, Peter
** CW: Who? Me? You must be joking!! **
email: peter(no-spam-filler)@frenning.dk
http://www.frenning.dk/oz1pif.htm
Ph. +45 4619 3239
Snailmail:
Peter Frenning
Ternevej 23
DK-4130 Viby Sj.
Denmark
***********************************
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
--
I am using the free version of SPAMfighter.
We are a community of 6 million users fighting spam.
SPAMfighter has removed 302 of my spam emails to date.
Get the free SPAMfighter here: http://www.spamfighter.com/len
The Professional version does not have this message
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
--
I am using the free version of SPAMfighter.
We are a community of 6 million users fighting spam.
SPAMfighter has removed 1605 of my spam emails to date.
Get the free SPAMfighter here: http://www.spamfighter.com/len
The Professional version does not have this message
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
--
I am using the free version of SPAMfighter.
We are a community of 6 million users fighting spam.
SPAMfighter has removed 1605 of my spam emails to date.
Get the free SPAMfighter here: http://www.spamfighter.com/len
The Professional version does not have this message
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
--
I am using the free version of SPAMfighter.
We are a community of 6 million users fighting spam.
SPAMfighter has removed 302 of my spam emails to date.
Get the free SPAMfighter here: http://www.spamfighter.com/len
The Professional version does not have this message
|