TenTec
[Top] [All Lists]

Re: [TenTec] 041 firmware rev

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] 041 firmware rev
From: "Jim M." <jmiller1706@cfl.rr.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 27 Feb 2009 16:51:35 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Be very careful guys, I now cannot get the previous version to work.
Downloads to the O2 OK, but the controls do not work.  Guess it's back to
the factory.

-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of Jim M.
Sent: Friday, February 27, 2009 4:42 PM
To: 'Discussion of Ten-Tec Equipment'
Subject: Re: [TenTec] 041 firmware rev

On the phone with TT, he suggested various reset sequences but the load
won't work.  Said file might have been corrupted and to download it again,
still no luck.  Now reverting back to previous version, hope I didn't crash
my radio.  Could someone give me that download site again just to be sure?

-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of kc9cdt@aol.com
Sent: Friday, February 27, 2009 4:13 PM
To: tentec@contesting.com
Subject: Re: [TenTec] 041 firmware rev

Make sure stop on error is ON,
Lee










-----Original Message-----
From: Jim M. <jmiller1706@cfl.rr.com>
To: 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
Sent: Fri, 27 Feb 2009 4:04 pm
Subject: Re: [TenTec] 041 firmware rev



Well not having a lot of luck here.  Somehow crashed the O2 first time
trying with an old serial card in the PC, and it was very slow.  Got a USB
to serial converter and it flashed in about 5 mins this time but nothing in
the radio works, no knob, no buttons, and the display reads all zeros
frequency.  Am trying the flash again.  Stay tuned.  So far I am
underwhelmed.

-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of Peter Frenning [OZ1PIF]
Sent: Friday, February 27, 2009 3:57 PM
To: Ron Castro; Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] 041 firmware rev

Ron Castro skrev:
> I have noticed that the levels between the AF and RF AGC's are quite 
> different.  The AF is very low compared to RF.
>
>          Ron Castro
>  Chief Technical Officer
>     Results Radio, LLC
>                N6IE
>       www.N6IE.com
>   
Same here, but doesn't seem to have detrimental effects other than you 
have to twist up the AF encoder...

-- 
Vy 73 de OZ1PIF/5Q2M, Peter

** CW: Who? Me? You must be joking!! **
email: peter(no-spam-filler)@frenning.dk
http://www.frenning.dk/oz1pif.htm
Ph. +45 4619 3239
Snailmail:
Peter Frenning
Ternevej 23
DK-4130 Viby Sj.
Denmark
***********************************


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>