Rick, I have my doubts that AOR would be clued up on older TT kit.. but will
give them a call once Christmas is over.
I did ask the very nice Chinese gentleman who mans the TT rally stall, and
he knew nothing about older TT gear. He knew about the RX320 / 340 and
Jupiter, but that's all.
Froeliche Weinachten Rick..
Paul.
----- Original Message -----
From: "Rick Westerman" <Rick@dj0ip.de>
To: <tentec@contesting.com>
Sent: Wednesday, December 24, 2003 2:20 PM
Subject: RE: [TenTec] Why leave out calibration information TT????
> Paul,
>
> Why don't you call Ten-Tec Direct and ask them?
>
> Their number is 01773 880788 (Derbyshire).
>
> 73
> Rick
>
> -----Original Message-----
> From: tentec-bounces@contesting.com
> [mailto:tentec-bounces@contesting.com]On Behalf Of Paul
> Sent: Wednesday, December 24, 2003 2:16 PM
> To: tentec@contesting.com
> Subject: Re: [TenTec] Why leave out calibration information
> TT????
>
> I too would like the answer to the question below.
>
> I have an Omni V, and would like to investigate the lopsided PBT
> tuning that
> it has.. but I don't want to do a "screwdrivers expert" job on it
> in case
> things worsen :-)
>
> So to recap, does anyone know the correct alignment procedure for
> the
> Ten-Tec Omni V model 562.
>
> I don't really want to make expensive transatlantic phone calls
> for
> information that really should be in the manual. My Japanese
> FT-102 has full
> alignment instructions in the user manual, and it is about the
> same age as
> the TT radio.
>
> Paul MW0CDO in South Wales UK.
>
> Seasons' greetings to all!
>
> ----- Original Message -----
> From: <OTAKEBI@aol.com>
> To: <tentec@contesting.com>
> Sent: Tuesday, December 23, 2003 4:09 PM
> Subject: [TenTec] Why leave out calibration information TT????
>
>
> > Why does TT make such complete Manuals for the OMNI V and VI
> and then
> leave
> > out basic information such as setting of IC Limit, Internal ALC
> Limit, FWD
> and
> > REF adjustment,
> > Meter Offset, etc.?
> > I had to make two long distance calls to TT just to get the
> information
> for
> > ALC calibration.
> > I spoke to a very nice Tech and asked if the information that
> was lacking
> in
> > the Manual could be found in a Service Manual or Supplement I
> could buy
> and he
> > told me that no such thing exist.
> > How does TT recalibrate a rig?
> > I don't think that each Tech is expected to keep it in their
> head.
> > Does anyone on this reflector know if a place exist that this
> information
> can
> > be bought or located?
> > Thanks,
> > Dan N4VET
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|