If anyone can do printscreen of SO2r RTTY settings for MK2R+ in writelog and
urouter soundcard + mmtty I had been very happy I was little confused by trying
get it work too
---Sent by iphoneLB3RE LJ3RE K3RAG ex: LA6FJAwww.lb3re.com ~ Rag ~ Stein Roar
Brobakken e-mail:post@lb3re.com
On 20. mai 2014 13:10:19 CEST, Richard Thorne <rthorne@rthorne.net> wrote:
Group, Thanks to Dean, Joe and Steve (GW4BLE) I determined that I had to go
into the windows sound system and select the 2 channel option as described
below. Both instances of MMTTY are now receiving the proper signal and
demodulating correctly. Now on to the transmit issue which I'll tackle this
evening. I have a sneaking suspicion that it has to do with the way I have my
com ports setup. I'll report back when I get it resolved. After I get all of
this working, I'll look at installing OCX Thanks Rich - N5ZC On 5/19/2014
8:49 AM, Dean St. Hill wrote: Rich Welcome to the twilight zone. Been
there. Many times. To see the way the sound cards are set-up within your
system - click on the Audio-switching tab of MK2R+. then click on "soundcard" -
over on the right 2/3 down the window. Even though the MMTTY plugin works,
I would suggest that it might be a good idea to actually use the "OCX" set-up
guideline as this is a more modern driver with the possibility of also using
"2tone" as an alternative to MMTTY. if you're setting audio from the left
channel in both windows - 1st make sure the buttons on MK2R+ are set correctly.
That's the top right section of MK2R. If that is correct then you need to go to
windows sound system - right click on the "speaker logo" in the system tray.
Choose recording devices. in the recording devices double-click the USB codec.
Then choose "advanced" tab - extreme right top of the new window. You will
then see a drop-down with "default format" - this is where you need to choose a
stereo option. Your current default is probably a mono option. I choose 2
channel, 16 bit 44100Hz (CD Quality) and this has always worked for me but I am
almost sure it can be a much much lower quality - others with more expertise
may jump in and help with guidance here. Finally after clicking the
necessary "OK" etc. return to the two MMTTY windows and just confirm that left
channel has been set up for your radio 1 and right channel for your radio 2.
Hmmm... you may also want to go back to router as well and under audio
switching tab re-confirm that the "use line out channel" has also been set for
radio one and radio 2. both may be set as "left". you should now be good to
go as far as dual receive. let's get that going and then check the tx side
of the equation. 73 and best regards, Dean - 8P6SH On
Mon, May 19, 2014 at 7:37 AM, Richard Thorne <rthorne@rthorne.net> wrote:This
is a cross post to Writelog and Microham. I've been working on configuring an
MK2R+ SO2R controller with a pair of K3's and my Win 7 Pro computer. I've been
able to get SSB and CW to work properly. I'm hung up on RTTY using MMTTY.
I've downloaded the setup guide from Microham and have setup two directories
and two instances of MMTTY, I also have the MMTTY plug in for Writelog
installed. If I select the test button for FSK on the MK2R+ ports tab for rig
1 I get diddling same goes for rig 2. While in Writelog I've followed the
setup instructions by first selecting rig 1 and starting MMTTY from the
appropriate directory, same for rig 2. However, I can't get either to diddle.
In addition, both instances of MMTTY appear to be getting the same audio from
rig 1 from the phone jack. I've selected the right and left audio source on
the misc tab while in TNC setup. On the sound card tab in TNC setup I've
selected Reception: Microphone (3 - USB Audio CODEC) and Transmission: Speakers
(3 - USB Audio CODEC) How does one determine which device identifier to select
on the misc tab in tnc setup? I thought it would be 3 but I'm obviously
incorrect. I want to to use the line out on the rear of the K3's to grab the
audio since it's fixed and won't be affected by the volume control of either
K3. The frustrating part is that I had this MK2R+ working just fine on RTTY
with one K3, adding the 2nd K3 has been a challenge. Is there an updated setup
guide specifically for Win 7? I'm half tempted to dust off an XP Pro laptop
and give that a try, Win 7 makes things very challenging. Thanks in advance
for any assistance. Rich - N5ZC
_______________________________________________ WriteLog mailing list
WriteLog@contesting.com http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/ -- Dean St.Hill
Counterpoint Consulting 17 Ocean City St.Philip Barbados
246-266-8230 246-416-5277 dmsthill@gmail.com __._,_.___
Posted by: Richard Thorne <rthorne@rthorne.net> Reply via web post
• Reply to sender • Reply to group • Start a New Topic •
Messages in this topic (1) This list is for the exchange of
information about the use and operation of microHAM products. Anyone with
specific hardware support issues should contact microHAM support at
mailto:support@microHAM.com. Visit Your Group New Members 3 •
Privacy • Unsubscribe • Terms of Use . __,_._,___
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|