Rich
Welcome to the twilight zone. Been there. Many times.
To see the way the sound cards are set-up within your system - click on the
Audio-switching tab of MK2R+. then click on "soundcard" - over on the right
2/3 down the window.
Even though the MMTTY plugin works, I would suggest that it might be a good
idea to actually use the "OCX" set-up guideline as this is a more modern
driver with the possibility of also using "2tone" as an alternative to
MMTTY.
if you're setting audio from the left channel in both windows - 1st make
sure the buttons on MK2R+ are set correctly. That's the top right section
of MK2R. If that is correct then you need to go to windows sound system -
right click on the "speaker logo" in the system tray. Choose recording
devices. in the recording devices double-click the USB codec. Then choose
"advanced" tab - extreme right top of the new window. You will then see a
drop-down with "default format" - this is where you need to choose a stereo
option. Your current default is probably a mono option.
I choose 2 channel, 16 bit 44100Hz (CD Quality) and this has always worked
for me but I am almost sure it can be a much much lower quality - others
with more expertise may jump in and help with guidance here.
Finally after clicking the necessary "OK" etc. return to the two MMTTY
windows and just confirm that left channel has been set up for your radio 1
and right channel for your radio 2.
Hmmm... you may also want to go back to router as well and under audio
switching tab re-confirm that the "use line out channel" has also been set
for radio one and radio 2. both may be set as "left".
you should now be good to go as far as dual receive.
let's get that going and then check the tx side of the equation.
73 and best regards,
Dean - 8P6SH
On Mon, May 19, 2014 at 7:37 AM, Richard Thorne <rthorne@rthorne.net> wrote:
> This is a cross post to Writelog and Microham.
>
> I've been working on configuring an MK2R+ SO2R controller with a pair of
> K3's and my Win 7 Pro computer.
>
> I've been able to get SSB and CW to work properly.
>
> I'm hung up on RTTY using MMTTY. I've downloaded the setup guide from
> Microham and have setup two directories and two instances of MMTTY, I also
> have the MMTTY plug in for Writelog installed.
>
> If I select the test button for FSK on the MK2R+ ports tab for rig 1 I get
> diddling same goes for rig 2.
>
> While in Writelog I've followed the setup instructions by first selecting
> rig 1 and starting MMTTY from the appropriate directory, same for rig 2.
> However, I can't get either to diddle.
>
> In addition, both instances of MMTTY appear to be getting the same audio
> from rig 1 from the phone jack. I've selected the right and left audio
> source on the misc tab while in TNC setup.
>
> On the sound card tab in TNC setup I've selected Reception: Microphone (3
> - USB Audio CODEC) and Transmission: Speakers (3 - USB Audio CODEC)
>
> How does one determine which device identifier to select on the misc tab
> in tnc setup? I thought it would be 3 but I'm obviously incorrect. I want
> to to use the line out on the rear of the K3's to grab the audio since it's
> fixed and won't be affected by the volume control of either K3.
>
> The frustrating part is that I had this MK2R+ working just fine on RTTY
> with one K3, adding the 2nd K3 has been a challenge. Is there an updated
> setup guide specifically for Win 7?
>
> I'm half tempted to dust off an XP Pro laptop and give that a try, Win 7
> makes things very challenging.
>
> Thanks in advance for any assistance.
>
> Rich - N5ZC
>
>
>
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
--
*Dean St.Hill*
*Counterpoint Consulting *
*17 Ocean City*
*St.Philip*
*Barbados*
*246-266-8230 <246-266-8230>*
*246-416-5277 <246-416-5277>*
*dmsthill@gmail.com <dmsthill@gmail.com>*
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|