I have nothing to really add to this thread other than to vent my frustration.
Kevin alluded to it with his criticism of the Flex and xvtrs. I'm particularly
disappointed with Yaesu and their "flagship" radio (FTDX101D / MP). No
configuration or low level output for transverter interfacing. I knew that
before purchasing the radio and planned to continue to use my FT1000MP MKV as
an IF but the '101 has many nice features I'd like to have when using it with
transverters for 2m and up. A significant oversight by Yaesu IMHO.
73,
Ed K3DNE
> On 01/16/2023 11:24 AM Kevin Hobbs via VHFcontesting
> <vhfcontesting@contesting.com mailto:vhfcontesting@contesting.com > wrote:
>
>
> Thanks Terry ... that's what I figured ... I assume if the K3 does that
> then
> K4 probably follows the same architecture. Seems like just another VHF+ /
> XVTR oversight by Flex Radio. 73 KH
>
>
> -----Original Message-----
> From: Terry Price <terry@directivesystems.com
> mailto:terry@directivesystems.com >
> Sent: January 16, 2023 10:40 AM
> To: 'Kevin Hobbs' <ve3kh@icloud.com mailto:ve3kh@icloud.com >
> Cc: 'VHF Contesting Reflector' <vhfcontesting@contesting.com
> mailto:vhfcontesting@contesting.com >
> Subject: RE: [VHFcontesting] IF Radios & XTRs
>
> Hi Kevin,
>
> Don't know about the K4 but I have four K3's and they remember every VHF
> band so when I QSY say to 222.100 and then to another band, when I come
> back
> to 222, it is on 222.100 and the same mode. The K3 supports 10 VHF bands
> so
> one radio can do 50 MHz (native) through 10GHz and the dial shows the
> correct frequency. Each band can have a frequency correction of +/- 5 KHz
> (maybe 10 I can't remember) and the band data is standard BCD that is also
> mirrored for HF. There is a separate control line that goes low when low
> power transverter mode is selected so you can differentiate between HF and
> VHF and there is a PTT output, all of these signals are available at the
> HD15 acc connector on the back. So you can cover 160m through 10 GHz all
> automatically with the right BCD decoder setup. If you get one with the
> internal 2m transverter, it can be set up to cover bands from 902 and up
> as
> an I.F.
>
> 73,
>
> Terry - W8ZN
>
> -----Original Message-----
> From: VHFcontesting
> [mailto:vhfcontesting-bounces+terry=directivesystems.com@contesting.com
> mailto:vhfcontesting-bounces+terry=directivesystems.com@contesting.com ] On
> Behalf Of Kevin Hobbs via VHFcontesting
> Sent: Monday, January 16, 2023 10:30 AM
> To: VHF Contesting <vhfcontesting@contesting.com
> mailto:vhfcontesting@contesting.com >
> Subject: [VHFcontesting] IF Radios & XTRs
>
> Hi
>
>
>
> I have a Flex 6600M and a number of XVTRs connected to its XVTRA RXA ports
> with external switching controlled via the Flex IO USB
>
> * 8 CH Relays to control DPDT coax switch to select between a Kuhne
> 144 XVTR (which is the IF for 10 24 47 GHz XVTRs) and a Q5 5-Band XVTR
>
>
>
> My issue is that when I change VHF+ bands via the Flex, it resets my freq,
> panadapter etc to default settings and so I can switch back to where I was
> when running the bands because the Flex thinks it all 28MHz and even
> though
> it handles all the XVTR's it doesn't have any band memory / persistence
> for
> XVTRs. This makes running the bands and going back and forth to
> coordinate a
> feal nuisance.
>
>
>
> Does anyone have a workaround or know if some other HF IF rigs handle this
> better ie: K3 or K4 ???
>
>
>
> 73 Kevin VE3KH
>
> _______________________________________________
> VHFcontesting mailing list
> VHFcontesting@contesting.com mailto:VHFcontesting@contesting.com
> http://lists.contesting.com/mailman/listinfo/vhfcontesting
>
>
> _______________________________________________
> VHFcontesting mailing list
> VHFcontesting@contesting.com mailto:VHFcontesting@contesting.com
> http://lists.contesting.com/mailman/listinfo/vhfcontesting
>
_______________________________________________
VHFcontesting mailing list
VHFcontesting@contesting.com
http://lists.contesting.com/mailman/listinfo/vhfcontesting
|