VHFcontesting
[Top] [All Lists]

Re: [VHFcontesting] [FFMA] MAST FOR ROVERS

To: "vhfcontesting@contesting.com" <vhfcontesting@contesting.com>
Subject: Re: [VHFcontesting] [FFMA] MAST FOR ROVERS
From: jimk8mr--- via VHFcontesting <vhfcontesting@contesting.com>
Reply-to: jimk8mr@aol.com
Date: Mon, 9 Aug 2021 23:06:32 +0000 (UTC)
List-post: <mailto:vhfcontesting@contesting.com>
I'm not sure how well it would hold beams at sufficient heights, but for HF 
roving I use a 33 ft fiberglass mast held up with a tripod of two four foot 
surplus aluminum mast sections for legs, with a tripod casting available from 
www. goverticalusa.com. Those same four foot mast sections ought to be OK for a 
mast to hold a small six meter beam.
I can send photos to those who might be interested.


73  -  Jim   K8MR




-----Original Message-----
From: Jim Johnson <jim@kc4hw.com>
To: FFMA@groups.io <FFMA@groups.io>; vhfcontesting@contesting.com
Sent: Mon, Aug 9, 2021 5:19 pm
Subject: Re: [VHFcontesting] [FFMA] MAST FOR ROVERS

I 
don't think the following would represent the best solution, but I too have 
been thinking about this and thought that I would try to use some of the 1m 
fiberglass military poles.  My thought was to used adjustable clamps above and 
below each joint., with a total of 5 pieces that you be a length of 16'-
9".  Which would perhaps give enough height to clear vicinity obstacles, like 
vehicles, RV, tents, etc

Been working on a 3L 6m antenna and probably just the one antenna to start 
with.  I believe that this mast would support a HO Loop for 2m and/or 70cm as 
well.  Perhaps a small rotor could be installed at the 2nd joint.  I think the 
"Armstrong" rotor with be my initial method.

My biggest concern is managing a scope out pole, as I am now 73 I don't think 
that I will be getting any stronger in the coming years.  hi hi.  

I definitely would be interested in what others have to suggest.

Jim/KC4HW - EM71 Alabama


----- Original Message -----
From: Robert W5AJ <woodr90@gmail.com>
Reply-To: <FFMA@groups.io>
To: <FFMA@groups.io>
Sent: 8/9/2021 2:43:56 PM
Subject: [FFMA] MAST FOR ROVERS


Recently purchased a mast support for Truck receiver hitch.  "Portable" five 
element beam is in possession.  What type of portable masts are being used that 
can be easily carried inside pickup bed or short SUV?????

73 W5AJ

The mast support:  https://smile.amazon.com/gp/product/B07ZGBRT61   I'm not 
recommending it or otherwise, hopefully it works for Rover use - parked. 
_._,_._,_


Groups.io Links:
You receive all messages sent to this group. 
View/Reply Online (#14056) | Reply To Group | Reply To Sender | Mute This Topic 
| New Topic
Your Subscription | Contact Group Owner | Unsubscribe [jim@kc4hw.com]

_._,_._,_
_______________________________________________
VHFcontesting mailing list
VHFcontesting@contesting.com
http://lists.contesting.com/mailman/listinfo/vhfcontesting
_______________________________________________
VHFcontesting mailing list
VHFcontesting@contesting.com
http://lists.contesting.com/mailman/listinfo/vhfcontesting
<Prev in Thread] Current Thread [Next in Thread>