VHFcontesting
[Top] [All Lists]

Re: [VHFcontesting] Setting up TE RF amp for use with a sequencer.

To: KC2TN <kc2tn@comcast.net>
Subject: Re: [VHFcontesting] Setting up TE RF amp for use with a sequencer.
From: James Froemke <jim.k0mhc@earthlink.net>
Date: Sun, 15 Dec 2019 21:56:22 -0600
List-post: <mailto:vhfcontesting@contesting.com>
Don’t blow up the internal pre-amp accidentally.  The RF sense protects against 
losing the hardwired PTT. 

> On Dec 15, 2019, at 8:49 PM, KC2TN <kc2tn@comcast.net> wrote:
> 
> I’d be interested in what they tell you regarding the pin 5-6 jumper. 
> 
> I’m looking to disable this as well. 
> 
> Joe - KC2TN 
> 
>> On Dec 15, 2019, at 6:30 PM, John Young via VHFcontesting 
>> <vhfcontesting@contesting.com> wrote:
>> 
>> 
>> Taking pin 2 to ground turns on the PA with 5 and 6 still internally 
>> connected.  
>> 
>> However with 5 and 6 internally connected the rf sensing is still enabled 
>> which defeats part of the purpose of the sequencer.  The amplifier can turn 
>> on if RF gets to it even if the PTT ground to rf amp lead from the sequencer 
>> is not grounded.  
>> 
>> I have had my 991A on 6m buzz my 1.25m amp, same thing happened with the 
>> W4IY Elecraft on 6m in september.  If I had been using a hard keyed pre amp 
>> on 1.25m it would have been fried.
>> 
>> I opened up the amp and there is no obvious sign of the pin 5-6 internal 
>> shorting wire.  Maybe you have to cut a trace now?
>> 
>> 
>> Calling TE Tomorrow.
>> 
>> 73
>> John
>> KM4KMU 
>> On Sunday, December 15, 2019 John Young via VHFcontesting <nosigma@aol.com> 
>> wrote:
>> 
>> The TE manual gives some simple instruction for hard keying the amplifier 
>> but out an abundance of caution I want to verify my understanding of them 
>> before I start cutting wires and adding relays.
>> 
>> The DEMI sequencer gives a sequenced PTT ground to enable the amplifier.  
>> The TE  instructions are to cut the internal  shorting wire between pins 5 & 
>> 6 and then connect the PTT ground to pin 2.
>> 
>> To enable the RF amplifier the TE instructions are:  1) Connect pin 5 & 6 
>> then 2) connect pin 2 to PTT ground.
>> 
>> My interpretation of these instruction are:
>> I need to use the PTT ground to close a relay that connects pins 5 & 6 and 
>> then use an output from this relay to close another relay that connects the 
>> PTT ground to pin 2 on the amplifier.
>> 
>> Is this correct?
>> Is there a better way?
>> 
>> 73
>> John
>> KM4KMU 
>> 
>> 
>> _______________________________________________
>> VHFcontesting mailing list
>> VHFcontesting@contesting.com
>> http://lists.contesting.com/mailman/listinfo/vhfcontesting
>> _______________________________________________
>> VHFcontesting mailing list
>> VHFcontesting@contesting.com
>> http://lists.contesting.com/mailman/listinfo/vhfcontesting
> 
> _______________________________________________
> VHFcontesting mailing list
> VHFcontesting@contesting.com
> http://lists.contesting.com/mailman/listinfo/vhfcontesting

_______________________________________________
VHFcontesting mailing list
VHFcontesting@contesting.com
http://lists.contesting.com/mailman/listinfo/vhfcontesting
<Prev in Thread] Current Thread [Next in Thread>