VHFcontesting
[Top] [All Lists]

[VHFcontesting] Re: [Mw] Powering microwave amps from portablesupplies

To: <vhfcontesting@contesting.com>
Subject: [VHFcontesting] Re: [Mw] Powering microwave amps from portablesupplies
From: stan@capecod.com (Stan)
Date: Thu Jun 19 16:44:51 2003
Hello Bob,

Multiple classes of service:

For the minimalist: battery powered equipment focusing on 12.6 VDC and 
solar, photovoltaic, charger

For the average once or twice a year portable operator:  Use the mobile 
battery and charger.
        Start up the engine to charge the battery when voltage goes 
below 12.0 VDC

For the few times a year portable operator: Deep discharge batteries 
charged by mobile charger , or solar charger
        adding more batteries can give you more power or higher voltage 
like 2 each 12 V batteries in series for 24 VDC

For the dedicated ROVER operator: a minimum of a 1000W HONDA AC 
generator and DC power supplies for required DC voltages
        consider the SAMLEX 23 amp, 13.8 VDC switch mode power supply 
for a light and compact PS.
        consider the HONDA EU1000iA2  generator as advertised in 
QSTreet, 629$      http://www.mayberry.com/generators
            for a quiet, clean sinewave generator. Consider the 
accessories like cover and service and parts manual. Larger quiet units 
are available.

    With a AC generator you have AC for the antenna rotators, electrical 
lights, soda cooler,  and the KW power supplies.
        Also AC power for the logging laptop computer.

Standardize on DC voltages like 13.8 VDC and/or 28.0 VDC.

Reportedly Pyro Joe's 3.4 GHz 40W bricks will play OK with 13.8 VDC and 
lower duty sideband operations, instead of the 12.6 VDC as suggested.

I will advise later on the AVANTEK brick power supply issues.

Stan, WA1ECF





kr7o@vhfdx.com wrote:

> I am looking at incorporating a 10w Avantek 5.7G and one of the 3.4G 
> Toshiba amps into my portable microwave station and I am curious as to 
> what other people are using for regulated supplies for the odd and in 
> some cases fairly critical voltages needed to power these amps.  In 
> the case of the Avantek, I am talking about the modified units 
> requiring +10.5v and -12v, and of course the 12.6v for the Toshiba amps.
>
> For portable operations I typically use two 12v deep cycle batteries 
> that will range in voltage between 11.5v and 13v over the course of 
> the discharge cycle.  -12v shouldn't be a problem, but I haven't found 
> zeners or other voltage regulators of the proper voltage and current 
> ratings for the other voltages.  12.6v is even more of a challenge 
> without some sort of DC-DC converter (but again I haven't found any 
> surplus converters that match the needed conditions).
>
> I could always build an AC power supply for the proper voltages, but 
> then I need to carry a potentially noisy inverter (and the overhead 
> necessary to power that).   Resistive voltage dividers are a 
> possibility, but still do not provide the level of regulation that 
> appears to be needed to protect these devices, and also waste precious 
> battery stores.
>
> So, what is everyone using to supply these amps.  Hopefully I am 
> missing something simple here.
>
>
>
>
> 73, Robert KR7O/YB2ARO, DM07ba/OI52ee  (ex.  N7STU)
> kr7o@vhfdx.com
>
> www.vhfdx.com (Norcal WSWSS activities & KR7O/YB2ARO homepages)
>
>
>
> _______________________________________________
> Microwave mailing list
> microwave@wa1mba.org
> http://mbs.valinet.com/mailman/listinfo/microwave
>
>


<Prev in Thread] Current Thread [Next in Thread>