Thanks to all for your suggestions and good explanations. I appreciate the time
and effort you took to reply.
73, Rich, N6KT
From: Stan K2STN <k2stn@frontier.com>
To: towertalk@contesting.com
Sent: Tuesday, May 22, 2018 9:14 PM
Subject: Re: [TowerTalk] Amount of "Goop" to use in Telescoping Aluminum
Tubing Connections?
Also, a thought from the electrician side of the fence. I had to learn
this because my brother-in-law bought a 60's vintage aluminum wired
house and asked for some help with its wiring.
When working with aluminum wiring, especially old stuff, it's been found
that it's best to have the scotchbrite pad being used to clean the wires
to be filled with Noalox.
The understanding is that aluminum almost immediately skins over with
oxide after being dry abrasively cleaned. Having the Noalox in the pad
puts down a film that protects the cleaned surface from re-oxidation.
Aluminum oxide is an insulator.
They found this out when investigating failed junctions made with wire
nuts that had proven to be faulty and had caused house fires. What they
discovered was that the only path between the twisted wires of the
junction was through the metal threading of wirenut itself, which is not
designed to carry current. It was making the circuit because the
wirenut's threads had cut through the oxide completing the connection
between the twisted together oxide insulated wires.
Stan
On 5/22/2018 9:05 PM, Bob Shohet, KQ2M wrote:
> Hi Rich,
>
> You want just enough of a thin film to provide lubrication and to prevent
> corrosion/oxidation – no more lest you partially or completely insulate one
> section of the telescoping tubing from the other. (I put too much one time
> and had to take the antenna down to wipe it off because the swr and bandwidth
> was way off!)
>
> NOW what I do is as follows:
>
> I put on a pair of large nitrile gloves ($20 for a box of 400 at Costco) and
> put about 1/2” of Noalox on one glove and then grasp the tubing and smear it
> on with my hand in a circular motion up and down a few times for about 3’ on
> the element. (I know it reads like something obscene but it is not. LOL!)
>
> Then I take a paper towel and gently grasp the tubing and wipe off and go up
> and down and the paper towel takes most of it off and leaves a thin
> continuous film all the way around the element.
>
> Since I adopted that method, I have never put too much on nor have I had a
> problem taking apart an element years later.
>
> The best part is that you do not get any goop on your hands or hands – clean
> up is really easy - you just throw the gloves and the paper towels in the
> garbage and you are done!
>
> 73
>
> Bob KQ2M
>
>
> From: Richard Smith
> Sent: Tuesday, May 22, 2018 8:04 PM
> To: towertalk@contesting.com
> Subject: [TowerTalk] Amount of "Goop" to use in Telescoping Aluminum Tubing
> Connections?
>
> "Goop" = Penetrox, Noalox, Jet-Lube SS-30, or other
>
> A while back, there was a good discussion on this reflector of which goop is
> recommended for telescoping aluminum tubing connections in antennas. My
> question here is not intended to recap all of the "Which Goop is Better"
> points, but rather to ask how much goop to use. Over the years, I have heard
> recommendations from "very minimal" to "lots".
>
> I would be interested in recommendations from this very experienced group.
> The trade-offs in my mind are:
> Very minimal amount: Pros: Allows the aluminum to aluminum contact to provide
> the electrical connection. The goop provides some lubrication, maybe some
> corrosion protection. Cons: Not enough
> corrosion protection, not much help in separating telescoping parts when
> desired years later.
> Lots of Goop: Pros: Assists in making a good electrical connection,
> provides more corrosion protection, easier to separate parts when desired
> years later
> Cons: Maybe too much lubrication, harder to
>get hose clamps tight enough to prevent unwanted slippage.
> Maybe this is very basic, but I am interested in your comments.
>
> Thanks in advance,
> 73, Rich, N6KT
>
>
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|