Towertalk
[Top] [All Lists]

[TowerTalk] Anchor Bolt Material

To: <towertalk@contesting.com>
Subject: [TowerTalk] Anchor Bolt Material
From: "Wilson" <infomet@embarqmail.com>
Reply-to: Wilson <infomet@embarqmail.com>
Date: Sun, 12 Oct 2014 23:01:23 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
New holes??
WL

-----Original Message----- From: towertalk-request@contesting.com
Sent: Sunday, October 12, 2014 12:00 PM
To: towertalk@contesting.com
Subject: TowerTalk Digest, Vol 142, Issue 17

Send TowerTalk mailing list submissions to
towertalk@contesting.com

To subscribe or unsubscribe via the World Wide Web, visit
http://lists.contesting.com/mailman/listinfo/towertalk
or, via email, send a message with subject or body 'help' to
towertalk-request@contesting.com

You can reach the person managing the list at
towertalk-owner@contesting.com

When replying, please edit your Subject line so it is more specific
than "Re: Contents of TowerTalk digest..."


Today's Topics:

  1. Yaesu Rotor Controller Anomaly (Tony)
  2. Anchor bolt material (Marvin Shelton)


----------------------------------------------------------------------

Message: 1
Date: Sat, 11 Oct 2014 17:01:45 -0400
From: Tony <dxdx@optonline.net>
To: towertalk@contesting.com
Subject: [TowerTalk] Yaesu Rotor Controller Anomaly
Message-ID: <54399AB9.4070303@optonline.net>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed

All:

A peculiar thing happened with my Yaesu 2800 rotor controller today. The
rotor kept returning to it's preset position after turning it either
clockwise or counter clockwise. It also moved very slowly.

My first thought was that the preset circuit must be bad, but then I
noticed that the problem went away when I pulled on the preset button.
It turned out that the button itself was jammed. Tapping on it a few
times allowed it to return to it's normal position.

I noticed what appeared to be a tiny piece of plastic which could have
worked it's way into the button causing it to jam. Might be a fluke, but
thought I'd pass it on.

Tony -K2MO


------------------------------

Message: 2
Date: Sun, 12 Oct 2014 08:37:25 -0700
From: Marvin Shelton <marvs@att.net>
To: towertalk@contesting.com
Subject: [TowerTalk] Anchor bolt material
Message-ID: <B3A98427-689D-4D50-B893-C4A24AEA78C8@att.net>
Content-Type: text/plain; charset=utf-8

Here?s a question for everyone. I?m installing a new T-base for my crank-up US Tower so that I can use the raising fixture and stop climbing it when it?s retracted. (getting too old for that) and I?ve got the holes prepared and am wondering about the anchoring material to use. I?ve drilled the holes 2.5? in diameter to account for the nuts at the base of the anchor bolts, which I?ve had to cut off because I couldn?t go deep enough. So now I have 2.5? diameter holes to install 1-1/8? anchor bolts in.

My obvious choices are anchoring epoxy, which is expensive at over $20 per tube, Quikrete anchoring cement, and I just discovered something called Rockite- for anchoring and patching. I?m hoping that any of these choices will work. I?d like to save a few $$ and use the Quikrete which will be much easier to use (mix like concrete and pour into the holes). It has a pull-out strength of 14,100 psi after 24 hours and 21,000 psi after 28 days.

Anyone have experience with any of these products. I?d like to do my pour today if possible.

Thanks in advance.


Marv
wa2bfw@arrl.net





------------------------------

Subject: Digest Footer

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk


------------------------------

End of TowerTalk Digest, Vol 142, Issue 17
******************************************
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>