I am heading to Bermuda for CQ 160 signing VP9/N1SNB. I'll be running
an inverted L with 100watts.
I'm a 160 novice. Any tips for low power, off shore operating from my
distinguished colleagues on the Top Band list?
73, jeff n1snb
-----Original Message-----
From: topband-bounces@contesting.com
[mailto:topband-bounces@contesting.com] On Behalf Of
topband-request@contesting.com
Sent: Wednesday, January 21, 2009 7:03 AM
To: topband@contesting.com
Subject: Topband Digest, Vol 73, Issue 28
Send Topband mailing list submissions to
topband@contesting.com
To subscribe or unsubscribe via the World Wide Web, visit
http://lists.contesting.com/mailman/listinfo/topband
or, via email, send a message with subject or body 'help' to
topband-request@contesting.com
You can reach the person managing the list at
topband-owner@contesting.com
When replying, please edit your Subject line so it is more specific
than "Re: Contents of Topband digest..."
Today's Topics:
1. Re: South Dakota (Ed Gray W0SD)
2. PSK & RTTY (wb0m@Flashdog.us)
3. Re: CQ 160 weird ideas (mstangelo@comcast.net)
4. Re: Coax (Paul Christensen)
5. Recycled ferrites for 160m (G4GED Dave)
6. Re: Coax (Stan Stockton)
7. Running an Inv L to top of tower (AD5VJ Bob)
8. QRQ vs QRS (Lars Harlin)
9. arizona sunshine (PACER99@aol.com)
10. Re: QRQ vs QRS (Dan Zimmerman N3OX)
11. Re: Recycled ferrites for 160m (Dan Zimmerman N3OX)
----------------------------------------------------------------------
Message: 1
Date: Tue, 20 Jan 2009 09:02:50 -0600
From: Ed Gray W0SD <w0sd@triotel.net>
Subject: Re: Topband: South Dakota
To: calle.jonsson@sverige.nu
Cc: topband@contesting.com
Message-ID: <4975E79A.1020400@triotel.net>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed
W0SD will be very active in the CQ 160 contest. QRV with 1/4 wave
vertical with 135 radials, drooping dipole at 195 feet and 4 beverages
and receiving loop, Alpha 99 @ 1500 watts and Elecraft K3
Ed W0SD
------------------------------
Message: 2
Date: Tue, 20 Jan 2009 09:15:39 -0600
From: wb0m@Flashdog.us
Subject: Topband: PSK & RTTY
To: topband@contesting.com
Message-ID: <A7DB3FCE-69DA-40A3-BD79-1081BBD42EB8@Flashdog.us>
Content-Type: text/plain; charset=US-ASCII; format=flowed; delsp=yes
Hello Everyone,
After a long, long time I'm finally using PSK-31 and RTTY. Is there
much activity on 160 and and is it below 1.810 or is there a
"preferred" frequency? What about the digital contests?
Tnx & 73, Jeff/wb0m/Nebraska
------------------------------
Message: 3
Date: Tue, 20 Jan 2009 15:33:47 +0000 (UTC)
From: mstangelo@comcast.net
Subject: Re: Topband: CQ 160 weird ideas
To: LA5HE Ragnar Otterstad <la5he@otterstad.dk>
Cc: topband@contesting.com
Message-ID:
<1368723235.3125711232465627343.JavaMail.root@sz0121a.westchester.pa.mai
l.comcast.net>
Content-Type: text/plain; charset=utf-8
All,
We should add K to the signal report to indicate clicks - 599k. It would
add some meaning to a useless signal report since all exchanges are 599
anyway.
Mike N2MS
------------------------------
Message: 4
Date: Tue, 20 Jan 2009 10:40:56 -0500
From: "Paul Christensen" <w9ac@arrl.net>
Subject: Re: Topband: Coax
To: <topband@contesting.com>
Message-ID: <018c01c97b15$7c64cbc0$203ca8c0@D2GPY9C1>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original
> "For receive I use RG-6/U quad shield from Home Depot. As I recall a
500
> foot roll costs between $50 and $100 (closer to $50). It works great."
Equally good for Rx is the flooded, direct-bury RG-6 QS. I'm a refugee
from
the CATV industry and have developed an appreciation for Snap-'N-Seal
"F"
connectors. DXE supplies high quality SNS hardware -- and Home Depot
supplies the Ideal Industries brand compression tools and SNS connectors
at
reasonable prices. SNS hardware can also be found under the Thomas &
Betts
and Augat brand names.
A reliable SNS fitting requires a coaxial cable prep tool designed for
the
SNS connector and equally important, a contour-blade cable cutter to
prevent
the RG-6 cable from being crushed as it's cut.from the spool.
Paul, W9AC
------------------------------
Message: 5
Date: Tue, 20 Jan 2009 22:52:59 -0000
From: "G4GED Dave" <radiodave.g4ged@tiscali.co.uk>
Subject: Topband: Recycled ferrites for 160m
To: <topband@contesting.com>
Message-ID: <2A65F1B531FA4679AB341599A2BEF88C@SN046981320192>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original
Hi Topbanders,
My query revolves around the suitability, for 160m applications, of
recycled
ferrite material extracted from redundant CRT TVs and PC Monitors ?
Thanks to the Flat-screen revolution, there's now lots of this recycled
ferrite freely available from CRT - Flat upgrading. There's lots of
satisfaction to had saving all this good stuff from simply ending up
wasted
in another land fill project and it costs nothing !
There's the big chunky dougnut/bagel shaped ferrite core from the
scanning
coil yoke, two of which, as common mode chokes, have successfully killed
my
160m-ADSL RFI stone dead.
I have several doing service as chokes in RX antenna feeders. They seem
to
work but how well, I've no means of knowing?
Most PCs and monitor mains power leads incorporate an embedded chunky
tubular ferrite, easily removed with a hot air gun and craft knife.
There's often a variety of other small ferrite rings, tubes and beads
etc to
be had from within this redundant equipment.
Does anyone know what ferrite "mixes" all these are likely to be or how
they
could be simply tested at home for suitability as rf xfmrs, baluns,
chokes
etc on Topband ?
Thanks
Dave
------------------------------
Message: 6
Date: Tue, 20 Jan 2009 17:34:53 -0600
From: "Stan Stockton" <stan@aqity.org>
Subject: Re: Topband: Coax
To: "Paul Christensen" <w9ac@arrl.net>, <topband@contesting.com>
Message-ID: <6FB6CD570BC04B76B5631082A5E5DF81@n42qnuurv8xdmc>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=response
----- Original Message -----
From: "Stan Stockton" <k5go@cox.net>
To: "Paul Christensen" <w9ac@arrl.net>; <topband@contesting.com>
Sent: Tuesday, January 20, 2009 5:32 PM
Subject: Re: Topband: Coax
>> Equally good for Rx is the flooded, direct-bury RG-6 QS. I'm a
>> refugee from
>> the CATV industry and have developed an appreciation for Snap-'N-Seal
>> "F"
>> connectors. DXE supplies high quality SNS hardware -- and Home Depot
>> supplies the Ideal Industries brand compression tools and SNS
>> connectors at
>> reasonable prices. SNS hardware can also be found under the Thomas &
>> Betts
>> and Augat brand names.
>
> DXE is 2.5 times the price of Technical Connections for the connectors
> and the selection is better for tools and connectors at the less
> expensive source.
>
> Stan, K5GO
------------------------------
Message: 7
Date: Tue, 20 Jan 2009 22:05:51 -0600
From: "AD5VJ Bob" <rtnmi@sbcglobal.net>
Subject: Topband: Running an Inv L to top of tower
To: <topband@contesting.com>
Message-ID: <029701c97b7d$8d171b40$6601a8c0@RAD9FBHB71>
Content-Type: text/plain; charset="us-ascii"
Since I am limited for tower height (30 feet) I am thinking of
installing a 20 meter mast at the top of my tower and then running a
wire from the bottom of the tower to the top of the mast out from the
tower about 10 feet (inverted L style) and then across from
the top of the mast about 50 feet to top of a 30 foot fiberglass
extendable pole on which I have mounted at the present time an 80
meter inverted V with the apex at the top of the pole.
I would mount the wire just below the apex of the 80 meter inv V.
My question is (I have seen this done on some web pages):
Can I mount my three element tribander (to make room for the L at the
top) to the side of the tower with the tower in between some
of the elements?
I have seen this done on some web pages where people have stacked beams
along the length of the tower and then rotated the tower
instead of using a standard rotor, just not sure if it can be done
without affecting the beam characteristics or the L's
characteristics.
73 fer nw es gud DX,
QSL VIA: LotW, BUR, e-QSL
Bob AD5VJ
http://www.ad5vj.com/
Old Calls WB5ZQU, WY5L/KH3, KE5CTY, N5IET
------------------------------
Message: 8
Date: Wed, 21 Jan 2009 06:33:16 +0100
From: "Lars Harlin" <lars.harlin@one.se>
Subject: Topband: QRQ vs QRS
To: <topband@contesting.com>
Message-ID: <6C5E440AE70F4F17BFBDF03FFD8431F7@larsdc0e265da7>
Content-Type: text/plain; charset="iso-8859-1"
Hi folks!
Ever since I came on Topband, about 20 yers ago, is has been an
unwritten custom to use fairly low speed CW for DX'ing on TB.
My experience is that it's usually easier to copy using QRQ (i.e. 20 -30
WPM) as there are almost always QSB on DX signals. With slow speed it
can be a hard time to be able to copy all the letters in the call before
diving into a QSB valley...
Any other thoughts?
73 de Lars, SM3BDZ
------------------------------
Message: 9
Date: Wed, 21 Jan 2009 02:02:22 EST
From: PACER99@aol.com
Subject: Topband: arizona sunshine
To: topband@contesting.com
Message-ID: <d22.352da387.36a8227e@aol.com>
Content-Type: text/plain; charset="US-ASCII"
well, this was the night of the year! europe, europe and more europe. i
will
remember it for a long time.
good luck to all topbanders this weekend. see you in the contest!
73,
larry
n7dd
**************Inauguration '09: Get complete coverage from the nation's
capital.
(http://news.aol.com/main/politics/inauguration?ncid=emlcntusnews0000000
3)
------------------------------
Message: 10
Date: Wed, 21 Jan 2009 09:03:36 -0500
From: Dan Zimmerman N3OX <n3ox@n3ox.net>
Subject: Re: Topband: QRQ vs QRS
To: topband@contesting.com
Message-ID:
<141cfb1e0901210603n1d3d641ge49fc0ade43ab98d@mail.gmail.com>
Content-Type: text/plain; charset=ISO-8859-1
> My experience is that it's usually easier to copy using QRQ (i.e. 20
-30
> WPM) as there are almost always QSB on DX signals. With slow speed it
can be
> a hard time to be able to copy all the letters in the call before
diving
> into a QSB valley...
Lars,
If I have a needed station who CQs in my face whenever I call, I will
always
switch speeds a couple times before giving up.
I usually leave the keyer at 20WPM because that seems to be a good
compromise between QRS and having a hard time timing things out in
pileups.
But I'll try faster or slower if I have trouble getting through... and
will
QRQ if I find the station I'm trying to work has short, sharp fading. I
think it's important to consider that slow speed might be hurting you
depending on condx.
73
Dan
------------------------------
Message: 11
Date: Wed, 21 Jan 2009 09:23:29 -0500
From: Dan Zimmerman N3OX <n3ox@n3ox.net>
Subject: Re: Topband: Recycled ferrites for 160m
To: topband@contesting.com
Message-ID:
<141cfb1e0901210623h4a8ab724wdbff269faa2ec119@mail.gmail.com>
Content-Type: text/plain; charset=ISO-8859-1
>
> I have several doing service as chokes in RX antenna feeders. They
seem to
> work but how well, I've no means of knowing?
>
If you have an antenna analyzer you can get a decent idea of how the
thing
works by winding a few turns of wire onto the core and measuring the
impedance of that. Shooting for a total impedance around 50 ohms is
useful
for something like the MFJ-259B which is more accurate around 50 ohms
than
way out in high and low impedance land.
Once you know the impedance of the N turns you just wound on the core,
you
can guess that the impedance of the finished choke of M turns will be
(M/N)^2 .
As a final check, I sweep the finished choke across HF and look for the
first low impedance series resonance, just to make sure it's not in my
frequency range of interest or close to the top end. It's not useful
to
measure the impedance of the choke directly since the impedance range of
my
MFJ-259B is only up to 650 ohms, but it just lets me know that the
choke's
not diving to nothing in the range I'm measuring in.
If you had a signal generator and an oscilloscope you could build a
voltage
divider with a known resistor of 1k or so and the choke and measure the
voltage across the choke as a function of frequency with a known applied
voltage, and get a direct measure of the magnitude of the impedance of
the
choke that way (and if you've got a couple high impedance scope probes
instead of just one you could technically get the phase, and therefore
the
complete R+jX). You do have to be a bit careful about stray
capacitances,
etc, but since you're posting to Topband it's not so severe at 1.8MHz in
the
way it would be at 30MHz or higher.
> Does anyone know what ferrite "mixes" all these are likely to be or
how
> they
> could be simply tested at home for suitability as rf xfmrs, baluns,
chokes
> etc on Topband ?
I've never found one that is an often used ham mix since most of these
things are for ~100kHz applications, but I have found a few that are
reasonably useful chokes.
As far as baluns and other power handling applications go (and even
receiving transformers), you need to be a little more careful because of
potential problems with core loss (which depend on the balun design and
application).
If you build a simple 4:1 balun to go from 50 to 200 ohms and intend to
use
it that way, the easiest home test is to build TWO of them and connect
them
back to back into a dummy load to transform from 50 ohms to 200 ohms
back to
50 ohms. Then you run power through and measure power in and power out.
You can't figure out that there's 0.05735dB loss this way, but since 1dB
total loss will give you 79W out for 100W applied, you can easily
measure a
pair of random baluns/ununs and determine that they have <0.5dB loss
apiece. You can also measure the effects of core heating if there is
any
and you can do so at the power level you want to run.
Small receiving transformers could also be tested for loss the same way,
back to back, but a signal generator and oscilloscope would probably be
needed (though maybe you could use a signal generator, a step
attenuator,
and your receiver)
73
Dan
------------------------------
_______________________________________________
Topband mailing list
Topband@contesting.com
http://lists.contesting.com/mailman/listinfo/topband
End of Topband Digest, Vol 73, Issue 28
***************************************
_______________________________________________
Topband mailing list
Topband@contesting.com
http://lists.contesting.com/mailman/listinfo/topband
|