Carl: You are looking at another thread that is on-going. The Omni VI series
does NOT have thatweird ram chip. The logic board on the VI series has a
battery that is replaceable. I know this fora fact since I have one that I am
looking at right now and the other logic board in my hand. The
eprom that Pete is looking for is the 27C64 from the logic board and it is the
same one that TenTecused in all three revisions. The board I have came from a
revision 3 radio. The revision 3 was afactory option that included the 9 mhz
if board that allows two "narrow" filters. You may interchange
the logic eprom without any problems. I do have the instruction sheet here
with too.
Clayton N4EV
From: Carl Moreschi <n4py3@earthlink.net>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Sent: Wednesday, February 11, 2015 10:45 AM
Subject: Re: [TenTec] WTB: part from junker Omni VI option 1 rig
No, not that one. This is a RAM chip, not the microprocessor with built
in EPROM.
Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com
On 2/11/2015 10:26 AM, Barry N1EU wrote:
> Just to check - Carl, you're not referring to the Omni V chip discussed on
> another thread?
>
> Barry N1EU
>
> On Wed, Feb 11, 2015 at 3:13 PM, Carl Moreschi<n4py3@earthlink.net> wrote:
>
>> It's not the EPROM chip. There's no burning. It's a RAM chip with a
>> built in battery.
>>
>> Carl Moreschi N4PY
>> 58 Hogwood Rd
>> Louisburg, NC 27549
>> www.n4py.com
>>
>>
>> On 2/11/2015 8:54 AM, Clayton Brantley via TenTec wrote:
>>
>>> I would talk with Gary at TenTec. They have a few oldies that they could
>>> pull a epromor perhaps burn another one.
>>>
>>> Clayton N4EV
>>>
>>> From: Barry N1EU<barry.n1eu@gmail.com>
>>> To: Discussion of Ten-Tec Equipment<tentec@contesting.com>
>>> Sent: Tuesday, February 10, 2015 8:31 AM
>>> Subject: Re: [TenTec] WTB: part from junker Omni VI option 1 rig
>>>
>>> Have you tried calling Ten-Tec for the chip?
>>>
>>> Barry N1EU
>>>
>>> On Tue, Feb 10, 2015 at 8:29 AM, Peter Bertini<radioconnection@gmail.com>
>>> wrote:
>>>
>>> If anyone is parting out an Omni VI with the option 1 installed, I'd be
>>>> interested in buying the complete board and or just the upgrade chip.
>>>>
>>>> Not being able to individually lock A and B VFOs is a pain when chasing
>>>> split operations.
>>>>
>>>> Pete
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>
>>>
>>>
>>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>>
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|