Gary, which panadapter SDR are you using?
"Holes in the pileups?"
You must have poor antennas; there are no holes in the pileups.
You have to make your own hole! (hi)
73 - Rick, DJ0IP
(Nr. Frankfurt am Main)
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Gary - AB9M
Sent: Tuesday, December 23, 2014 3:07 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Eagle 9MHz tap questions.
Rick,
Carl's mod and a panadapter SDR in synch are great combination! The Y
connector avoids a potentially problematic IF tap. I've been using the
similar N4PY modification on my OMNI-VII for several years and find its
great for DXing and Contesting; the panadapter lets me see the holes in the
pile ups, places to fit my signal in and on TX it acts like a station
monitor - I can see what my signal looks like.
73 & DX,
Gary - AB9M
-----Original Message-----
From: Carl Moreschi
Sent: Tuesday, December 23, 2014 6:51 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Eagle 9MHz tap questions.
Rick,
You can just put a Y connector between the two preselector jacks and run the
third leg to a panadapter radio such as the Softrock Ensemble II.
This works great. My software will keep the softrock and Eagle on the same
frequency.
Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com
On 12/23/2014 1:18 AM, Drago wrote:
>
>
> -----Izvorna poruka----- From: Rick - DJ0IP / NJ0IP Sent: Tuesday,
> December 23, 2014 5:32 AM To: 'Discussion of Ten-Tec Equipment' Subject:
> Re: [TenTec] Eagle 9MHz tap questions.
> I was wanting to add a pan-adapter.
> I may have to replace a board in order to do that.
> My unit does not have the TMP jack with the 9 MHz out.
>
> Also I have to find a way to run the signal out the back.
> I already have two spare RCA Phono jacks in use for the pre-selector.
>
> 73 - Rick, DJ0IP
> (Nr. Frankfurt am Main)
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
> Richards
> Sent: Tuesday, December 23, 2014 2:49 AM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Eagle 9MHz tap questions.
>
> Are you going to add a panadapter ?
>
> ================== K8JHR ==================
>
>
> On 12/22/2014 2:46 PM, Rick - DJ0IP / NJ0IP wrote:
>> Is it just a tap, like perhaps a Y-connection, or does it also have a
> buffer stage?
>> Unfortunately my Eagle fell out of the nest before that feature was
>> added
> to the radio.
>> ____________________________________________
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|