That's the only way the 1708 works for what is needed. I have several
of my users doing this.
Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com
On 11/9/2014 9:56 AM, george fritkin via TenTec wrote:
To whomever reads this......using the jumper on the MFJ 1708 is not a good idea
George, W6GF
On Saturday, November 8, 2014 11:19 PM, Rick - DJ0IP / NJ0IP<Rick@DJ0IP.de>
wrote:
On the topic of antenna switches for multiple receivers, there are such
devices available.
One such device is the DA-4 from RF Systems.
See: http://www.universal-radio.com/catalog/preamps/0601.html
I've used this before but only with multiple receivers.
I don't know how well it behaves around RF.
The Eagle and Omni VII both have a mod which interrupts the RX antenna line
and routes it to the back panel. You could use the line out to drive a
switch and have the line in be one of the outputs of this device.
You would have to copy this mod for use with the OM6, which would be very
easy to do since there is a lot of space inside the OM6.
Or, do like I did and simply build your own 3-dB splitter. Mine is a in a
tiny square box about 2.5"x2.5"x1".
If you don't want to make the splitter yourself, they are available
commercially, such as the one from Mini Circuits, which claims only 0.3 dB
insertion loss (though this is only possible with a broadband amp (I
thought), yet I don't see any mention of an amp).
http://www.minicircuits.com/pdfs/ZFSC-2-6+.pdf
In the case of the Eagle, it inserts AFTER the RX-GND (protection) relay, so
it is safe to use "as is" for this purpose. I would have to look back at
the OM7 circuit diagram to see if it has the same type of protection relay.
If you d-i-y, you would need to add the protection relay yourself, just
before splitting the RX ant out.
This type of solution enables both receivers to work at the same time,
though usually with 3dB loss, which most of the time is not even noticeable.
73 - Rick, DJ0IP
(Nr. Frankfurt am Main)
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Don
Rasmussen via TenTec
Sent: Sunday, November 09, 2014 7:04 AM
To: tentec@contesting.com
Subject: Re: [TenTec] OT: Holiday SDR Project
Great info Carl - thanks.
Sounds like Corsair 2 has the best option for passing the receive but that
is not a CAT radio for N4PY software so yes, some external antenna switching
would be needed as you suggest. I prefer a universal solution so maybe the
MFJ or a DX Engineering RTR-1A and using the amp control line to activate
it.
I was never a big one for panadapters but figured with a $66 SDR receiver
there might be a simple/inexpensive solution for that - any way I look at it
seems to be a couple hundred dollars - hi...
=====================================================================
What radio are you using? Many radios have an easy way to share antennas. If
that's not an easy solution then the MFJ1708 can do the job. See below.
The solution to share antennas is to add an MFJ-1708 T/R switch. This unit
will automatically sense RF from the transmitter and then remove the
panadapter radio from the receive antenna connection. But the MFJ switch
will also remove the transceiver from the transmit connection while in
receive. So the MFJ switch needs a very simple mod. You must solder a 14
gauge wire between the transmit and antenna SO-239 connections. This will
then make the switch operate properly for this use. Additionally, you can
wire the relay to energize from your radio's amp key line for faster and
safer switching. Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549 www.n4py.com
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|