After being turned off all night, I powered up the Orion just wondering what
version/state of firmware would greet me. It booted up in 2.064 with a couple
of glitches requiring a master reset, but otherwise fully operational. Go
figure!
Thanks for all your help (again)
73, Art
> From: wesattaway@bellsouth.net
> To: tentec@contesting.com
> Date: Wed, 5 Oct 2011 09:40:20 -0500
> Subject: Re: [TenTec] Firmware download site
>
> The suggestions about trying a different cable and a different downloaded
> copy of the firmware are good. I use a USB-Serial converter cable with
> Windows7 and have had no problems.
>
>
> ----------------- Wes Attaway (N5WA) -------------------
> 1138 Waters Edge Circle, Shreveport, LA 71106
> 318-797-4972 (Office) - 318-393-3289 (Cell)
> Computer Consulting and Forensics
> -------------- EnCase Certified Examiner ---------------
>
> -----Original Message-----
> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
> On Behalf Of art davis
> Sent: Tuesday, October 04, 2011 11:14 PM
> To: TenTec reflector
> Subject: Re: [TenTec] Firmware download site
>
>
> If I just leave it alone without answering the questions or touching the
> radio, it will cycle itself through the SYSTEM LOADING page, followed by the
> questiions over and over.
>
> > From: wesattaway@bellsouth.net
> > To: tentec@contesting.com
> > Date: Tue, 4 Oct 2011 22:37:12 -0500
> > Subject: Re: [TenTec] Firmware download site
> >
> > What happens if you do a master reset and RAM clear, then radio off and
> on?
> >
> > What firmware does it show on boot up?
> >
> > ----------------- Wes Attaway (N5WA) -------------------
> > 1138 Waters Edge Circle, Shreveport, LA 71106
> > 318-797-4972 (Office) - 318-393-3289 (Cell)
> > Computer Consulting and Forensics
> > -------------- EnCase Certified Examiner ---------------
> >
> >
> > -----Original Message-----
> > From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
> > On Behalf Of art davis
> > Sent: Tuesday, October 04, 2011 10:32 PM
> > To: TenTec reflector
> > Subject: Re: [TenTec] Firmware download site
> >
> >
> > Curses, foiled again!
> >
> > I am now able to download the file (v. 2.064) from the wiki site (thanks
> > again) and then use the update utility to load it to the radio. After
> > loading all the lines of code, the installer utility declares that the
> file
> > was successfully installed and the radio displays "SYSTEM LOADING" as it
> > should. Then it asks me about resetting filters and clearing memories. But
> > no matter how I answer either question it momentarily displays "SYSTEM
> > LOADING" again and then asks the questions again. It repeats all this
> cycle
> > and never gets to the operational mode where it displays 14.250.
> >
> > I was able to install this version back when it first was released, but
> had
> > the same problem. I remember I had to repeat several installs before it
> > magically worked for some reason. So far, I haven't been so lucky this
> time.
> >
> > In comparison, both of the previous two versions (2.062 and 2.063) load
> > correctly with no issues.
> >
> > I read a couple of posts where it was suggested that the memory battery
> > might be low which could affect the bootup. My snaphat memory battery
> reads
> > 3.1 V which indicates to me that it was probably replaced when the factory
> > performed the v. 2 upgrade.
> >
> > Lastly, when I do a "verify program", the update utility indicates that
> the
> > load is correct and successfully installed.
> >
> > Any ideas about why one version would install and one not?
> >
> > > Date: Fri, 30 Sep 2011 19:07:10 -0500
> > > From: alan.n5na@gmail.com
> > > To: tentec@contesting.com
> > > Subject: [TenTec] Firmware download site
> > >
> > > I've placed a download link for version 2.064X11 on the TenTecWiki.
> > > Just go to the link Barry posted below and scroll to the bottom.
> > >
> > > 73, Alan N5NA
> > >
> > > > I appreciate all the help...Thanks to all!
> > > >
> > > > >/ From:w3krq at dejazzd.com
> > <http://lists.contesting.com/mailman/listinfo/tentec>
> > > > />/ To:tentec at contesting.com
> > <http://lists.contesting.com/mailman/listinfo/tentec>
> > > > />/ Date: Fri, 30 Sep 2011 16:54:10 -0400
> > > > />/ Subject: Re: [TenTec] Firmware download site
> > > > />/
> > > > />/ I CALLED TEN TEC THE FIRMWARE FOR THE 565 ORION WILL BE ON NEXT
> > WEEK. 73
> > > > />/ ROD
> > > > />/
> > > > />/ -----Original Message-----
> > > > />/ From: Richards
> > > > />/ Sent: Friday, September 30, 2011 4:34 PM
> > > > />/ To: Discussion of Ten-Tec Equipment
> > > > />/ Subject: Re: [TenTec] Firmware download site
> > > > />/
> > > > />/ Gee... almost Barry. There is no download link for Version
> > 2.064x11.
> > > > />/
> > > > />/ Nice site, however. Lots of good stuff on it.
> > > > />/
> > > > />/ ------------------
> > > > />/ Happy Trails.
> > > > />/ ======================= Richards / K8JHR
> > =========================
> > > > />/
> > > > />/ On 9/30/2011 06:19, Barry N1EU wrote:
> > > > />/
> > > > />/ > just go tohttp://tentecwiki.org/doku.php?id=orionfw#version_2
> > > > />/ >
> > > > />/ > 73, Barry N1EU
> > > > />/ > _______________________________________________
> > > > />/
> > > > /
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|