Ron wrote:
>Steve N4LQ wrote:
>
>
>
>>.7v? NOT GOOD. Do this:
>>Unplug everything from the Peg except for the 12v power, including the
>>computer. Turn it on. Measure the PTT again. If it still reads .7v, you've
>>got hardware problems. If it jumps up to 5v or so then you have something
>>plugged into either the assc. jack, key jack, or mic jack that is shorting.
>>
>>Steve Ellington
>>N4LQ@iglou.com
>>----- Original Message -----
>>From: "Ron" <k8fg@sbcglobal.net>
>>To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
>>Sent: Sunday, March 20, 2005 6:14 PM
>>Subject: Re: [TenTec] NO XMIT WITH PTT
>>
>>
>>
>>
>>
>>
>>>Steve N4LQ wrote:
>>>
>>>
>>>
>>>
>>>
>>>>I don't quiet follow you. Are you saying if you left click the TX Loop
>>>>button at the top, it goes into transmit or do you mean it allows you to
>>>>go
>>>>into transmit? If it's the former, it almost sounds like your PTT line is
>>>>shorted somewhere and when you "close the loop" in software, it transmits.
>>>>I still think you should download the TT software and try it first. That
>>>>will eliminate some confusion since it's rather basic.
>>>>Check the PTT voltage at the jack per the manual between Gnd and Ptt. You
>>>>should have between 4 and 5 volts.
>>>>Steve Ellington
>>>>N4LQ@iglou.com
>>>>----- Original Message -----
>>>>From: "Ron" <k8fg@sbcglobal.net>
>>>>To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
>>>>Sent: Sunday, March 20, 2005 4:57 PM
>>>>Subject: Re: [TenTec] NO XMIT WITH PTT
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>>Steve N4LQ wrote:
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>Ron
>>>>>>Tx Loop button? What's that? In the "Transmitter" menu, I have a "Enable
>>>>>>keying loop" button. Is that what you meant? I have mine disabled since
>>>>>>I
>>>>>>don't use a TT amp with the Peg. On your N4PY front panel, do you have
>>>>>>the
>>>>>>"Xmit Disable" activated? If so, disable it. Also check the "ACCInp"
>>>>>>button.
>>>>>>For microphone input it should be disabled.
>>>>>>If all this doesnt work, try the basic TenTec software and start all
>>>>>>over.
>>>>>>Out of ideas. 73
>>>>>>Steve Ellington
>>>>>>N4LQ@iglou.com
>>>>>>----- Original Message -----
>>>>>>From: "Ron" <k8fg@sbcglobal.net>
>>>>>>To: <tentec@contesting.com>
>>>>>>Sent: Saturday, March 19, 2005 2:16 PM
>>>>>>Subject: [TenTec] NO XMIT WITH PTT
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Hello to the Group,
>>>>>>>I have a couple of questions .
>>>>>>>I have a Pegasus that will not Xmit via the Mic or Acc jacks
>>>>>>>but will key via the N4PY software with a mouse click on the
>>>>>>>TX Loop button.. Any ideas ?
>>>>>>>
>>>>>>>Also is there ant service info available ?
>>>>>>>Thanks, Ron/K8FG...
>>>>>>>_______________________________________________
>>>>>>>TenTec mailing list
>>>>>>>TenTec@contesting.com
>>>>>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>_______________________________________________
>>>>>>TenTec mailing list
>>>>>>TenTec@contesting.com
>>>>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>Hi Steve and Carl,
>>>>>I have the latest ver of software and in the top row of buttons there is
>>>>>a Tx Loop button after the Calibrate.
>>>>>When I left click on this button it will go into xmit. If I go into the
>>>>>settings/transmitter menu and
>>>>>uncheck Keying Loop the rig goes into xmit. ACCInp is disabled.
>>>>>I am starting to believe I have a rig problem, if I short the Ptt pin in
>>>>>the mic connector to ground
>>>>>there is no xmit also did the same test with the Acc connector with the
>>>>>same results.
>>>>>Ron/K8FG...
>>>>>_______________________________________________
>>>>>TenTec mailing list
>>>>>TenTec@contesting.com
>>>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>_______________________________________________
>>>>TenTec mailing list
>>>>TenTec@contesting.com
>>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>Hi Steve,
>>>When I left click the button it xmit's. I just checked the ptt voltage,
>>>it reads -.707 I don.t have a manual
>>>other than basic operation.
>>>Ron/K8FG...
>>>_______________________________________________
>>>TenTec mailing list
>>>TenTec@contesting.com
>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>>
>>>
>>>
>>>
>>_______________________________________________
>>TenTec mailing list
>>TenTec@contesting.com
>>http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>>
>>
>>
>Ok Steve, I will check this after dinner.
>Thanks, Ron/K8FG...
>_______________________________________________
>TenTec mailing list
>TenTec@contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
Hi Steve,
I unplugged all except pwr. still .7v, I checked this at the circuit
board plig-in and the same.
Following the circuit back from the board 4 pin jack there are 2
surface mount components.
The first closest to the jack end of the circuit measures .70 one one
side and .73 on the other
pos a chip res. When I check the 2nd chip component I measure the .73
and 4.6v on the outer side.
This suspect chip has a marking of EO1 or E01 on it, very hard to see.
Might be a cap. Any idea
what it is and it's value ?
Ron/K8FG...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|