Steve N4LQ wrote:
>I don't quiet follow you. Are you saying if you left click the TX Loop
>button at the top, it goes into transmit or do you mean it allows you to go
>into transmit? If it's the former, it almost sounds like your PTT line is
>shorted somewhere and when you "close the loop" in software, it transmits.
>I still think you should download the TT software and try it first. That
>will eliminate some confusion since it's rather basic.
>Check the PTT voltage at the jack per the manual between Gnd and Ptt. You
>should have between 4 and 5 volts.
>Steve Ellington
>N4LQ@iglou.com
>----- Original Message -----
>From: "Ron" <k8fg@sbcglobal.net>
>To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
>Sent: Sunday, March 20, 2005 4:57 PM
>Subject: Re: [TenTec] NO XMIT WITH PTT
>
>
>
>
>>Steve N4LQ wrote:
>>
>>
>>
>>>Ron
>>>Tx Loop button? What's that? In the "Transmitter" menu, I have a "Enable
>>>keying loop" button. Is that what you meant? I have mine disabled since I
>>>don't use a TT amp with the Peg. On your N4PY front panel, do you have the
>>>"Xmit Disable" activated? If so, disable it. Also check the "ACCInp"
>>>button.
>>>For microphone input it should be disabled.
>>>If all this doesnt work, try the basic TenTec software and start all over.
>>>Out of ideas. 73
>>>Steve Ellington
>>>N4LQ@iglou.com
>>>----- Original Message -----
>>>From: "Ron" <k8fg@sbcglobal.net>
>>>To: <tentec@contesting.com>
>>>Sent: Saturday, March 19, 2005 2:16 PM
>>>Subject: [TenTec] NO XMIT WITH PTT
>>>
>>>
>>>
>>>
>>>
>>>
>>>>Hello to the Group,
>>>>I have a couple of questions .
>>>>I have a Pegasus that will not Xmit via the Mic or Acc jacks
>>>>but will key via the N4PY software with a mouse click on the
>>>>TX Loop button.. Any ideas ?
>>>>
>>>>Also is there ant service info available ?
>>>>Thanks, Ron/K8FG...
>>>>_______________________________________________
>>>>TenTec mailing list
>>>>TenTec@contesting.com
>>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>>
>>>>
>>>>
>>>>
>>>_______________________________________________
>>>TenTec mailing list
>>>TenTec@contesting.com
>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>>
>>>
>>>
>>>
>>Hi Steve and Carl,
>>I have the latest ver of software and in the top row of buttons there is
>>a Tx Loop button after the Calibrate.
>>When I left click on this button it will go into xmit. If I go into the
>>settings/transmitter menu and
>>uncheck Keying Loop the rig goes into xmit. ACCInp is disabled.
>>I am starting to believe I have a rig problem, if I short the Ptt pin in
>>the mic connector to ground
>>there is no xmit also did the same test with the Acc connector with the
>>same results.
>>Ron/K8FG...
>>_______________________________________________
>>TenTec mailing list
>>TenTec@contesting.com
>>http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>>
>
>_______________________________________________
>TenTec mailing list
>TenTec@contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
Hi Steve,
When I left click the button it xmit's. I just checked the ptt voltage,
it reads -.707 I don.t have a manual
other than basic operation.
Ron/K8FG...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|