You can find out about Winkey at www.k1el.com.
Carl Moreschi N4PY
Franklinton, NC
----- Original Message -----
From: "K. Indart" <kitdart@ntelos.net>
To: <tentec@contesting.com>
Sent: Thursday, October 14, 2004 11:51 AM
Subject: RE: [TenTec] Jupe+n4py+mixw2
> Hi Carl
> Where can I find more info on the Winkey, it sound very good. TIS.
> 73, Ken WA4RPH
>
> -----Original Message-----
> From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]On
> Behalf Of Carl Moreschi
> Sent: Thursday, October 14, 2004 7:31 AM
> To: tentec@contesting.com
> Subject: Re: [TenTec] Jupe+n4py+mixw2
>
> I am right now adding support for the K1EL Winkey keyer to my
> pegasus/jupiter program. This resolves all keying issues with my program.
> I already have added this support to my Orion program. The winkey keyer
is
> a fantastic and inexpensive software controlled keyer, allowing keyboard
or
> paddle operation simultaneously.
>
> Carl Moreschi N4PY
> Franklinton, NC
> ----- Original Message -----
> From: "Charles Greene" <W1CG@QSL.NET>
> To: <tentec@contesting.com>
> Sent: Thursday, October 14, 2004 6:23 AM
> Subject: Re: [TenTec] Jupe+n4py+mixw2
>
>
> > Jerome,
> >
> > With MixW and the N4PY program, in MixW go Configure-TRCVR CAT/PTT-TEN
> > TEC-Pegasus \ Jupiter (emulation mode) and fill in the software path.
> Now
> > the MixW will import the frequency/andd/mode from MixW and control
> > frequency/band/mode. I use a hardware interface from MixW to the serial
> > port DRT or RTS line to the PTT line in the Jupiter in the Accessory
> > plug. This line is the same as the CW key line. The N4PY has a CW
> > keyboard, but I didn't try that while using MixW.
> >
> > 73,
> >
> > W1CG
> >
> > At 01:21 AM 10/14/2004, jerome schatten wrote:
> > >I googled on this and I think there may have been some discussion on it
> in
> > >2003, however I found nothing really relevant. I'm running a Jupiter
and
> > >most of my time is spent on cw. Occasionally, when I can't make my bug
go
> > >fast enough, long enough, I wish to use a keyboard to send. Using
MixW2
> > >meets my needs for a simple vox driven cw keyboard. N4py meets my needs
> for
> > >rig control. I'm using a rather lame p100 with 32 megs of which ram
> works
> > >ok using either programme, but as you might guess, not both at the same
> > >time.
> > >
> > >I'm going to be pushing my pIII 450 with 256 megs of ram down to the
> shack
> > >and getting rid of the p100 very shortly. My question is: Will I then
be
> > >able to use the N4PY software set for ssb to control the rig and MixW2
to
> > >send keyboard CW (MCW actually using the sound card and ssb.) and have
> them
> > >both up on the screen at the same time? I've listened to the note
> generated
> > >on my ft920, checked for crud on the sides and it seems ok as long as
> > >everything is set up properly. Or... is there a better way?
> > >
> > >So... was I compute bound with the lame machine or is there something
> else
> > >at work here? Appologies if this has been asked before.
> > >
> > >Jerome - VA7VV
> >
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|