Hi Carl
Where can I find more info on the Winkey, it sound very good. TIS.
73, Ken WA4RPH
-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]On
Behalf Of Carl Moreschi
Sent: Thursday, October 14, 2004 7:31 AM
To: tentec@contesting.com
Subject: Re: [TenTec] Jupe+n4py+mixw2
I am right now adding support for the K1EL Winkey keyer to my
pegasus/jupiter program. This resolves all keying issues with my program.
I already have added this support to my Orion program. The winkey keyer is
a fantastic and inexpensive software controlled keyer, allowing keyboard or
paddle operation simultaneously.
Carl Moreschi N4PY
Franklinton, NC
----- Original Message -----
From: "Charles Greene" <W1CG@QSL.NET>
To: <tentec@contesting.com>
Sent: Thursday, October 14, 2004 6:23 AM
Subject: Re: [TenTec] Jupe+n4py+mixw2
> Jerome,
>
> With MixW and the N4PY program, in MixW go Configure-TRCVR CAT/PTT-TEN
> TEC-Pegasus \ Jupiter (emulation mode) and fill in the software path.
Now
> the MixW will import the frequency/andd/mode from MixW and control
> frequency/band/mode. I use a hardware interface from MixW to the serial
> port DRT or RTS line to the PTT line in the Jupiter in the Accessory
> plug. This line is the same as the CW key line. The N4PY has a CW
> keyboard, but I didn't try that while using MixW.
>
> 73,
>
> W1CG
>
> At 01:21 AM 10/14/2004, jerome schatten wrote:
> >I googled on this and I think there may have been some discussion on it
in
> >2003, however I found nothing really relevant. I'm running a Jupiter and
> >most of my time is spent on cw. Occasionally, when I can't make my bug go
> >fast enough, long enough, I wish to use a keyboard to send. Using MixW2
> >meets my needs for a simple vox driven cw keyboard. N4py meets my needs
for
> >rig control. I'm using a rather lame p100 with 32 megs of which ram
works
> >ok using either programme, but as you might guess, not both at the same
> >time.
> >
> >I'm going to be pushing my pIII 450 with 256 megs of ram down to the
shack
> >and getting rid of the p100 very shortly. My question is: Will I then be
> >able to use the N4PY software set for ssb to control the rig and MixW2 to
> >send keyboard CW (MCW actually using the sound card and ssb.) and have
them
> >both up on the screen at the same time? I've listened to the note
generated
> >on my ft920, checked for crud on the sides and it seems ok as long as
> >everything is set up properly. Or... is there a better way?
> >
> >So... was I compute bound with the lame machine or is there something
else
> >at work here? Appologies if this has been asked before.
> >
> >Jerome - VA7VV
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|