Wow thanks Tom. I must have missed that one somehow. This will help me qsy a
little faster.
Steve
N4LQ
----- Original Message -----
From: "Tommy" <aldermant@alltel.net>
To: <tentec@contesting.com>
Sent: Sunday, May 09, 2004 3:43 AM
Subject: Re: [TenTec] band stacking
> Steve,
>
> That x10 is a 'feature' on the Orion. :>))) If you have the Step set to
10,
> push the MAIN RX button and it switches the step to 100 and the display
> changes to x10. Push the MAIN RX button again and your Step reverts back
to
> 10.
>
> Tom - W4BQF
>
> ----- Original Message -----
> From: "Steve Ellington" <N4LQ@igLou.com>
> To: "A. Sewell" <n5na@att.net>; <tentec@contesting.com>
> Sent: Saturday, May 08, 2004 11:30 PM
> Subject: Re: [TenTec] band stacking
>
>
> > Are you running cw using the internal keyer as I am Alan? I'm constantly
> > having some function either quit working or change on me. For example,
> the
> > tuning step menu just went nuts. and it was showing something like x10m
> on
> > the display instead just plain 10 as if it went to metric mode! I
finally
> > did a power reset and it cleared. Turning off the sweep seems to have
> > helped.
> > Steve
> > N4LQ
> >
> > ----- Original Message -----
> > From: "A. Sewell" <n5na@att.net>
> > To: <tentec@contesting.com>
> > Sent: Sunday, May 09, 2004 2:56 AM
> > Subject: Re: [TenTec] band stacking
> >
> >
> > > Steve,
> > >
> > > I don't think it's typical for the rig to lock up while running the
> sweep.
> > > I always run my sweep and rarely have any problems with the rig
locking
> > up.
> > > It has locked up before but it's been a long, long time.
> > >
> > > 73,
> > >
> > > Alan N5NA
> > >
> > > ----- Original Message -----
> > > From: "Steve Ellington" <N4LQ@igLou.com>
> > > To: <tentec@contesting.com>
> > > Sent: Saturday, May 08, 2004 9:46 PM
> > > Subject: Re: [TenTec] band stacking
> > >
> > >
> > > > I took you advice about turning off the sweep and just had 2 hours
of
> > > solids
> > > > QSO time without a reset. That sweep must eat up a lot of processor
> and
> > > > eventually lock up the rig. Wonder if the new firmware will fix
that?
> > > > Steve
> > > > N4LQ
> > > >
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> >
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|