Brett,
What version of knet do you have on the AP's? 4.44?
Dan
> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]
> On Behalf Of Brett Hays
> Sent: Thursday, January 29, 2004 9:37 PM
> To: Karlnet Mailing List
> Cc: rmallory@karlnet.com; Scot Green
> Subject: Re: [Karlnet] Hang up of the cell
>
> Sounds very similar to the problem we're having right now. This
past
> time
> we went 48 hours before it happened again, only for me, a simple
reboot
> won't do it, I have to change channels...weird.
>
> Answer me this:
>
> what hardware platform are you on? AP1000, KN200, Flashrom
>
> What are your clients using for hardware and how many are there? Do
you
> have any KN50's in the mix?
>
> I am very interested to hear your answers, as I'm sure Reg will be as
> well.
>
> ----- Original Message -----
> From: "Karlnet Posting Promo Systems" <karlnet@promosystems.nl>
> To: <karlnet@wispnotes.com>
> Sent: Thursday, January 29, 2004 3:23 PM
> Subject: [Karlnet] Hang up of the cell
>
>
> > Hello
> >
> > We have a large network in holland created with Turbocell
> > On this moment we have a strange problem with a POP location.
> >
> > The site situation is described as below.
> >
> > The problem is: The 2 cells works normal, ping times to the users
are
> 20ms
> > average.
> > Sometimes in the cells the ping times go from 20ms
> > -100-500-600-1200-2000-timeout
> > The interface monitor on the base says that the traffic is normal
(100
> > -300KByte/s)
> > But the user don't get much data en the ping times goes from timeout
-
> 2400ms
> > - timeout
> >
> > When I reset cell 2 the situation goes back to normal, pingtimes are
> back
> to
> > 20 - 30ms
> > Sometimes after cell 2 is back from reboot the same happens again
(3-4
> times)
> > Other times the cells stays good for several hours and then it
happens
> again.
> > Resetting the switch does the same.
> >
> >
> >
> > We have set the eth interfaces to full duplex / 10Mbit on advice of
> Karlnet
> > but it doesnt help.
> >
> > Does anyone an idea, please let me know
> >
> > Marco Eegdeman
> > Marco@promosystems.nl
> >
> > --------------
> >
> > Site Situation
> >
> > In the beginning we used ap1000 and wavepointII.
> > After the RG+ came available we replaced the WPII with the RG+
(KN100)
> >
> > Now we have a location with 2 cells and a PTP all on 2,4Ghz
> > The PTP is no TurboCell
> > Cell 1 = Ch1 (KN100)
> > Cell 2 = Ch9 (KN202) new RG+
> > PTP = Ch13
> >
> > Our Network on that location is:
> >
> > PTP => Linux Router => Switch => KN100 and a KN202 base ISP
> >
> > Our clients are bridged from the cell (RG1100 and Ubicom about 25
> clients
> in
> > each cell) to the base, from there the are routed to the Internet.
> >
> > 80% of the clients are NAT routed bij the linux router.
> > 20% of the users have a Public IP and are also routed bij the linux
> router
> >
> > We use the latest firmware 4.44.01 in the RG+ and the RG1100. The
> ubicoms
> are
> > of course factory default
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> --
> [This E-mail scanned for viruses by Declude Virus]
--
[This E-mail scanned for viruses by Declude Virus]
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
|