Doug,
Thanks, that did it. I have reloaded the Karlnet .bin file.
Jim
----- Original Message -----
From: "Support" <support@karlnet.com>
To: <karlnet@WISPNotes.com>
Sent: Tuesday, August 20, 2002 2:56 PM
Subject: RE: [Karlnet] Forced reload problem
> Jim,
>
> You do the Open Config File option. Very top of the File Menu. Select
the
> bin file and Import the key.
>
> When you go back to the File menu you will see the Upload Software.
>
> Doug Harman
> KarlNet, Inc.
> 525 Metro Place North
> Suite 100
> Dublin, OH 43017
> 614 822-5275 x 123
> 614 822-0024 fax
>
> > -----Original Message-----
> > From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]On
> > Behalf Of Jim
> > Sent: Tuesday, August 20, 2002 2:00 PM
> > To: karlnet@WISPNotes.com
> > Subject: Re: [Karlnet] Forced reload problem
> >
> >
> > I don't see any way to upload the .bin file to the AP. There is
> > no option to
> > "Upload Software" until after you Open the Remote Config. Config ver:
> > 3.86.10.
> >
> > Jim
> >
> > ----- Original Message -----
> > From: "Support" <support@karlnet.com>
> > To: <karlnet@WISPNotes.com>
> > Sent: Tuesday, August 20, 2002 12:28 PM
> > Subject: RE: [Karlnet] Forced reload problem
> >
> >
> > > Jim,
> > >
> > > In forced reload you can only upload software. You can not do an Open
> > > Remote or access the unit. This is normal and cannot be changed.
Load
> > the
> > > bin file in Forced reload and then reboot in normal operation
> > mode and you
> > > can access the unit.
> > >
> > > Doug Harman
> > > KarlNet, Inc.
> > > 525 Metro Place North
> > > Suite 100
> > > Dublin, OH 43017
> > > 614 822-5275 x 123
> > > 614 822-0024 fax
> > >
> > > > -----Original Message-----
> > > > From: karlnet-admin@WISPNotes.com
> > [mailto:karlnet-admin@WISPNotes.com]On
> > > > Behalf Of Jim
> > > > Sent: Tuesday, August 20, 2002 11:05 AM
> > > > To: karlnet@WISPNotes.com
> > > > Subject: [Karlnet] Forced reload problem
> > > >
> > > >
> > > > I have an AP-1000 in forced reload mode and I can use the
configurator
> > to
> > > > scan it. I then change the IP address and try to connect to the
> > > > unit. I get
> > > > a message back which says "Signature of remote bridge is not
> > recognized.".
> > > > Is there anyway to access the unit?
> > > >
> > > > Jim
> > > >
> > > >
> > > > _______________________________________________
> > > > Karlnet mailing list
> > > > Karlnet@WISPNotes.com
> > > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > > >
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
|