Karlnet
[Top] [All Lists]

RE: [Karlnet] Forced reload problem

To: <karlnet@WISPNotes.com>
Subject: RE: [Karlnet] Forced reload problem
From: "Support" <support@karlnet.com>
Reply-to: karlnet@WISPNotes.com
Date: Tue, 20 Aug 2002 14:56:17 -0400
List-post: <mailto:karlnet@WISPNotes.com>
Jim,

You do the Open Config File option.  Very top of the File Menu.  Select the
bin file and Import the key.

When you go back to the File menu you will see the Upload Software.

Doug Harman
KarlNet, Inc.
525 Metro Place North
Suite 100
Dublin, OH 43017
614 822-5275 x 123
614 822-0024 fax

> -----Original Message-----
> From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]On
> Behalf Of Jim
> Sent: Tuesday, August 20, 2002 2:00 PM
> To: karlnet@WISPNotes.com
> Subject: Re: [Karlnet] Forced reload problem
>
>
> I don't see any way to upload the .bin file to the AP. There is
> no option to
> "Upload Software" until after you Open the Remote Config. Config ver:
> 3.86.10.
>
> Jim
>
> ----- Original Message -----
> From: "Support" <support@karlnet.com>
> To: <karlnet@WISPNotes.com>
> Sent: Tuesday, August 20, 2002 12:28 PM
> Subject: RE: [Karlnet] Forced reload problem
>
>
> > Jim,
> >
> > In forced reload you can only upload software.  You can not do an Open
> > Remote or access the unit.  This is normal and cannot be changed.  Load
> the
> > bin file in Forced reload and then reboot in normal operation
> mode and you
> > can access the unit.
> >
> > Doug Harman
> > KarlNet, Inc.
> > 525 Metro Place North
> > Suite 100
> > Dublin, OH 43017
> > 614 822-5275 x 123
> > 614 822-0024 fax
> >
> > > -----Original Message-----
> > > From: karlnet-admin@WISPNotes.com
> [mailto:karlnet-admin@WISPNotes.com]On
> > > Behalf Of Jim
> > > Sent: Tuesday, August 20, 2002 11:05 AM
> > > To: karlnet@WISPNotes.com
> > > Subject: [Karlnet] Forced reload problem
> > >
> > >
> > > I have an AP-1000 in forced reload mode and I can use the configurator
> to
> > > scan it. I then change the IP address and try to connect to the
> > > unit. I get
> > > a message back which says "Signature of remote bridge is not
> recognized.".
> > > Is there anyway to access the unit?
> > >
> > > Jim
> > >
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>


<Prev in Thread] Current Thread [Next in Thread>