Amps
[Top] [All Lists]

Re: [Amps] Designing the Cleanest Linear with RF Negative Feedback

To: <amps@contesting.com>
Subject: Re: [Amps] Designing the Cleanest Linear with RF Negative Feedback
From: "Keith Dutson" <kdutson@sbcglobal.net>
Date: Wed, 14 Dec 2005 12:45:17 -0600
List-post: <mailto:amps@contesting.com>
Or, upgrade to the 9000 that puts out 75 Watts class A. :)

73, Keith NM5G

-----Original Message-----
From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On
Behalf Of TexasRF@aol.com
Sent: Wednesday, December 14, 2005 12:10 PM
To: K1JJ@comcast.net; amps@contesting.com
Subject: Re: [Amps] Designing the Cleanest Linear with RF Negative Feedback

 
2 cent reply de k5gw:
 
You will need a reliable test setup to know when you have reached your
design goals. You might consider starting with the test setup and do a
thorough evaluation of your FT1000D before beginning the amplifier project.
Depending on the results, you might have to adjust your expectations. One
possibility is that  the FT1000D power output could be reduced to say 50 or
100w and achieve IMD  levels you are wanting. This could eliminate two or
three stages of the PA  chain. No way to know without testing and adjusting
bias levels.
 
73,
Gerald K5GW
 
In a message dated 12/14/2005 11:49:58 A.M. Central Standard Time,
K1JJ@comcast.net writes:

Hi  All,

I'm planning to build up a 75M monoband amplifier that has at  least -45db
to -50db 3rd order IMD using heavy RF negative feedback. 10MW  in, 1500W
out.

I wanted to get opinions here what others thought was  the best general
configuration and perhaps suggest some real world  tubes.

It seems that the best amps that use RF feedback start with a  much larger
tube than generally used in open loop linears and run it about  half power .

I plan to use the 10 milliwatt output from my FT-1000D as  a source. This is
the low level stage just before it goes into the power  amp board. I'm
hoping this is class A stuff and a  much cleaner  starting point than its
-32db IMD 200W solid state power amplifier board  output. Any opinions on
that?

For this amplifier I am thinking of  either a chain of grounded grid stages
so that they have individual built  in feedback and an additional loop of
feedback around the whole  chain.

OR, use a tetrode final with regulated screen voltage with  stages going
back to amplify the 10MW level. Hopefully, use up to 15-20db  of  loop
feedback assuming the gain is available.

I would  appreciate any pointers to URLs showing working schematics of the
big  commerical amps that Collins, Harris, etc use, and ideas you may have
for  a design.

For example... I don't know what good low level tubes to use,  but lets just
say it went something like,  6AU6, 12BY7, 6146, 811A,  3-500Z,  GS-35B  -
all in grounded grid with an additional  feedback loop.

Or, for grid driven:  The same low level stages,  then 4CX-150, 4-1000A,
4CX-3000.  Looking for conservative ratings at  1500W and high IMD figures.

Another thing I wonder about is if a tube  like the 6146 or 4-1000A which
has 
modest IMD figures open looped,   can successfully participate in a -45 
to -50db IMD chain when big feedback  is used?

I will be building this amp over the next few months and will  post the
results once completed. Thanks in advance for any  help!

73,
Tom,  K1JJ

_______________________________________________
Amps mailing  list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps




_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>