Amps
[Top] [All Lists]

Re: [Amps] Boat-Anchor Cleanliness

To: <R@contesting.com>, <TexasRF@aol.com>
Subject: Re: [Amps] Boat-Anchor Cleanliness
From: "noddie" <noddie@comcast.net>
Date: Wed, 15 Mar 2006 16:14:10 -0800
List-post: <mailto:amps@contesting.com>
It makes it all so much easier when your wife is Ham, you even get to give your 
self a Radio Shack Xmas presents via the YL.

Mike

*********** REPLY SEPARATOR ***********



-----Original Message-----
From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On 
Behalf Of R@contesting.com
Sent: Wednesday, March 15, 2006 1:40 PM
To: TexasRF@aol.com
Cc: AMPS@contesting.com; ka1xo@juno.com
Subject: Re: [Amps] Boat-Anchor Cleanliness



On Mar 15, 2006, at 12:53 PM, TexasRF@aol.com wrote:

>
> Hal, I am absolutely in awe of a man having a wife that makes all that 
> acceptable. It is a scenario that the rest of us can only fantasize 
> about!

ï  There are bound to be some out there.  Maybe it's time to trade 
yours in on a new, lower-maintence model?
>
> 73,
> Gerald K5GW
>
>
>
> In a message dated 3/15/2006 2:43:21 P.M. Central Standard Time, 
> ka1xo@juno.com writes:
>
> Dear  Chris,
>
> Actually, I have washed dusty, cruddy circuit boards
> in the  sink many times. I always finish with an isopropanol scrub and 
> a hot  blow-dry. The alcohol mixes with the water and evaporates 
> without  residue.
>
> Hotel room bathrooms and kitchenettes are best for  this
> type of renovation. It avoids the inevitable discussion
> and  punishment when She Who Must Be Obeyed finds
> a single speck of PCBd.  splatter on a mirror or left
> on the porcelain. Further, the hair dryer in  electronics assembly 
> service is best done when alone and  undisturbed.
>
> In 37 years of traveling for business the development  of
> ham radio projects has found a time and place without
> the acrimony  and subsequent prostrations and begging
> for forgiveness when things like  hot blobs of solder happen to land 
> on a carpet.
>
> (One would think  that such lofty pursuits of knowledge
> would gain acceptance, but no.) A  good friend of mine
> was contemplating getting back on HF when  SWMBO
> discovered him in the yard with a coil of wire, looking for
> a  tie-point. His e-mail to me, complete with the ensuing scenario, 
> told of  his need to travel for business.
>
> I told him that for most of us, we  need to establish a secret room in 
> the cellar that only the pooch and  we know about, and to wear 
> headphones because the female ear is resonant  to heterodynes on 40 
> meters (Why do you think they named them HETEROdynes?  - Duh!) One 
> trace of a whistle and they're on the warpath, because we're  not 
> doing what's on the Current List.
>
> So again, travel has its ups  and downs. Ham Radio is mostly tinkering 
> and reading at this stage, so  getting all this out of the way now 
> smooths the relationship as it's out of  my blood and I am properly 
> comported for Domestic Responsibilities and  Assignments Subject to 
> Acceptance.
>
> Hal
> W4HBM
> On Wed, 15 Mar 2006  15:22:42 -0500 sb200 <sb200@optonline.net> 
> writes:
>> You should  have told him to use his 4000 psi power washer.  
>> Dishwasher.  Man O man
>>
>> Chris
>> -----  Original Message -----
>> From: "HAROLD B MANDEL"  <ka1xo@juno.com>
>> To: <amps@contesting.com>
>> Sent:  Wednesday, March 15, 2006 1:54 PM
>> Subject: [Amps] Boat-Anchor  Cleanliness
>>
>>
>>>
>>> 1. Old xfmrs that are  not completely potted
>>>    will be destroyed in the  dishwasher.
>>>
>>> 2. Even PWD's will be destroyed because  there
>>>    is always one little pinhole in the  tar.
>>>
>>> 3. All meters will be destroyed.
>>>
>>> 4. Probably all potentiometers will be
>>>   destroyed.
>>>
>>> 5. Aluminum panels that are not  coated
>>>    will tarnish and spot.
>>>
>>> All chassis renovation needs disassembly
>>> as far as is  humanly possible.  Most of my
>>> amplifier anchors have gone  right down to
>>> bare metal chassis with no hardware
>>>  remaining.
>>>
>>> Once there, it's easy to bring the  entire
>>> metalwork to the anodizer shop and have
>>> a  strip job and a brandy-new layer of
>>> Zinc-DiChromate  applied.
>>>
>>> On several occasions I needed to  add
>>> and subtract holes. Only then did I
>>> disassemble  everything all over again
>>> and bring it to the platers.
>>>
>>> For those who are not inclined, the
>>> "hand-bay  carwash" is a good
>>> alternative.  Afterward, use the
>>> hair dryer liberally.
>>>
>>> Hal
>>>  W4HBM
>>> _______________________________________________
>>> Amps mailing list
>>> Amps@contesting.com  
>>> http://lists.contesting.com/mailman/listinfo/amps
>>
>>
>>
>
>
> Harold Mandel
> Superintendent of Construction
> Baran Telecom  Inc.
> 606 - 205 -  0172
> hmandel@barantelecom.com 
> _______________________________________________
> Amps  mailing  list
> Amps@contesting.com http://lists.contesting.com/mailman/listinfo/amps
>
>
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com http://lists.contesting.com/mailman/listinfo/amps
>
>



Rich Measures, 805.386.3734, AG6K, www.somis.org


_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
<Prev in Thread] Current Thread [Next in Thread>