John,
No problem. The noise that occurs is so loud it hurts my ears when it happens
(wearing headphones). I believe that there is a combination or combinations of
settings that case the DSP to get a bad code load from the processor, which
causes the DSP to hang - there is no recovery that I can find short of powering
the rig off and on again, as you have found. Also note that the sub receiver
audio is likewise effected. The rest of the radio appears to function normally
in my case. Next time it happens, I'll make more detailed notes and post it
here
and to ditsnbits.
Also, once it occurs, I can repeatedly make it happen by merely cycling through
the BinRx choices. If it doesn't occur on the first time through the choices,
it
does so on the second or sometimes on the third. Weird.
73,
Lin
WB1AIW
John Nason / NA9U wrote:
> Lin,
>
> Thanks!! A local ham who has an Orion II and I were
> just discussing this noise that jumps up in the
> headphones. That makes three of us now.
>
> I have only been able to get rid of the noise by
> turning off the Orion and restarting.
>
> 73,
> John NA9U
>
> --- Lin Davis <linbdavis@earthlink.net> wrote:
>
>
>>I also have the white dot next to the STEP value on
>>my Orion II (2.030) using
>>COLOR 3.
>>
>>I also have a rare problem with audio when selecting
>>BinRX=Main (AUDIO Menu) and
>>is related to having NR and/or Notch on, as far as I
>>can tell. With headphones,
>>audio turns into very loud "digital" noise which
>>varies in intensity with the
>>sweep! When I pull the headphones plug out, the
>>noise is present through the
>>speaker.
>>
>>73,
>>Lin
>>WB1AIW
>>
>>John Nason / NA9U wrote:
>>
>>
>>>I have Orion II with 2.030. No white dot but yes
>>
>>I
>>
>>>drop characters on SEND1, 2 and 3. It is
>>
>>intermittent
>>
>>>and I never know when its going to happen. Seems
>>
>>like
>>
>>>the send buttons don't have a high enough priority
>>
>>to
>>
>>>the processor.
>>>
>>>73,
>>>John NA9U
>>>
>>>--- George K <w2yj@highstream.net> wrote:
>>>
>>>
>>>
>>>>I do a lot of contesting and DX'ing and what I
>>
>>have
>>
>>>>experienced with my new
>>>>O2 and not with my O1 is that I have my call
>>
>>stored
>>
>>>>in "SEND1". Every once
>>>>in a while when I press send1 to send my call it
>>>>seems to miss the first few
>>>>characters of my call and I must scramble to send
>>
>>it
>>
>>>>by hand.
>>>>I upgraded the firmware to 2.030 and it still
>>>>happens.
>>>>Has anyone else experienced this?
>>>>Also, I noticed a small white dot just to the
>>
>>right
>>
>>>>of the STEP number
>>>>toward the right hand side of the digit. It may be
>>
>>a
>>
>>>>small thing but does
>>>>anyone else notice it? It takes a while when the
>>>>sweep is on to appear. Turn
>>>>the rig off and back on and it's gone only to
>>
>>appear
>>
>>>>a while later. Look
>>>>closely at the far right of the digit. It doesn't
>>>>seem to pop up when the
>>>>sweep is off.
>>>>I noticed the same thing on the display O2 at
>>>>Orlando and mentioned it.
>>>>George
>>>>
>>>>
>>>>_______________________________________________
>>>>TenTec mailing list
>>>>TenTec@contesting.com
>>
>>>http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>>
>>>_______________________________________________
>>>TenTec mailing list
>>>TenTec@contesting.com
>>>
>>
>>http://lists.contesting.com/mailman/listinfo/tentec
>>
>>>
>>_______________________________________________
>>TenTec mailing list
>>TenTec@contesting.com
>>http://lists.contesting.com/mailman/listinfo/tentec
>>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|