Does the 301 work if you plug it thru the Y-adapter and have the other
side of the Y disconnected? If not, then you may have gotten a cable
that does not have all the pins wired.
73, Duane
On Tue, 4 Oct 2005 17:11:05 -0400 "Roger Borowski" <K9RB@bellsouth.net>
writes:
> Mike, I purchased one of these 3 way cables from the web site below
> and it
> arrived yesterday. I got both the serial port from the PC and the
> 301
> encoder connected to the cable and the cable plugged into the 564
> Omni VI
> Plus, which was really pretty simple. End result is that the 301
> encoder is
> totally unresponsive. I tried reversing the encoder DB-25 with the
> PC DB-25
> on the "Y" cable with the same results. The PC control works fine
> but the
> 301 remote encoder doesn't function at all. I then plugged just the
> 301
> remote encoder directly into the 564 Omni VI Plus and it functions
> just
> fine, as it should. Of course the PC to 564 also works fine, as it
> has in
> the past. I have the baud rate set at the default 1200 as well as
> the
> "address" code at the default of "04", where I always had it. I then
> played
> around with different baud rates to no avail as even up to 19200,
> the PC
> works fine but the 301 remote encoder does nothing when hooked up
> in
> parallel with the PC by way of the "Y" adapter, so went back to the
> 1200
> baud default setting. I'm stumped now and wonder if you or anyone
> else has
> any suggestions to a remedy for a situation I thought would be an
> easy, one
> minute hook-up without a second thought. By reversing the
> connections to the
> adapter cable and the PC still controlling the rig when connected to
> either
> DB-25 dongle, that pretty much eliminates a problem with the adapter
> cable.
> Help!
> Thanks in advance to anyone with a suggestion or solution!
> 73, -=Rog-K9RB=- K9RB@bellsouth.net
>
> ----- Original Message -----
> From: "Mike Coogan" <mikegc@pacifier.com>
> To: <tentec@contesting.com>
> Sent: Sunday, September 25, 2005 9:14 PM
> Subject: [TenTec] Fw: need info on connecting 301 encoder hook-up as
> well
> asPC toOmni VI Plus
>
>
> Roger, you could purchase one of these or build your own.
> http://www.opticsplanet.net/sports-radar-db25-y-cable.html
>
> Mike W7MGC
> Vancouver, Wa
>
> ----- Original Message -----
> From: "Roger Borowski" <K9RB@bellsouth.net>
> To: <TenTec@contesting.com>
> Sent: Saturday, September 24, 2005 6:41 PM
> Subject: [TenTec] need info on connecting 301 encoder hook-up as
> well as
> PC toOmni VI Plus
>
>
> >I recently found a model 301 encoder from TenTec's latest used
> >equipment list and was lucky enough to see the message right after
> it
> >was posted and called immediately and it was still available.
> > It arrived the other day and It is in excellent condition and
> works
> > fine when plugged into my Omni VI Plus. My question is how was it
> > intended to run both PC control and the encoder? Is it one or the
> > other or is there an adapter to add a second RS-232 type - 25 pin
> > connector to the rig? If so, are any available anyplace that
> anyone
> > can give me a lead on obtaining or do I have to homebrew one in a
> > small project box?
> > Thanks in advance, Rog-K9RB K9RB@bellsouth.net
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
Duane Calvin, AC5AA
Austin, Texas
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|