THANKS CARL for correcting me.
I apologize for misleading people (in my previous post on this
topic) by still living in the past.
To be honest, I've had Omni V / VI / V+ since the day each was
announced and I never noticed that it had changed from my older
Omni's.
Each time the rig shut down, I turned both Tcvr and P.S. off -
just as I always have in the past.
73
Rick
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]On Behalf Of Carl Moreschi
Sent: Wednesday, January 07, 2004 1:46 AM
To: tentec@contesting.com
Subject: Re: [TenTec] Omni 6+ Input vs Output power?
Rick,
With the Omni V, Paragon, Paragon II, Omni VI, Jupiter, and
Orion, there is
overcurrent protection built into the radio. The radio will
automatically
reduce its own drive to prevent the final current from going
above a set
threshold. The older Omni A and Omni D did not have this
protection. Also
the Pegasus does not have this over current protection.
Carl Moreschi N4PY
Franklinton, NC
----- Original Message -----
From: "Rick Westerman" <Rick@dj0ip.de>
To: <tentec@contesting.com>
Sent: Wednesday, January 07, 2004 12:42 AM
Subject: RE: [TenTec] Omni 6+ Input vs Output power?
> MIKE, BE CAREFUL
>
> Yes, the current consumption varies from band to band and when
> limiting to 20A, you may not always get 100w out.
>
> However, the 962 is incorporated in the protection circuitry of
> the Omni VI+ and has over-current shutdown (which I'm sure you
> have already experienced). If you use a non-T-T P.S., you
need
> to insert an external automatic circuit breaker in the line.
> These things typically come in values of 15A or 20A - dunno if
> you can get one for 22A. Without this circuit breaker, you run
a
> HIGH RISK of blowing your final transistors. DON'T SAY WE
DIDN'T
> TELL YOU if you blow the things!
>
> I recommend returning to using the Model 962 and forget about
the
> missing 10 watts on some bands. It will never be noticed in
any
> QSO.
>
> 73
> Rick
>
> -----Original Message-----
> From: tentec-bounces@contesting.com
> [mailto:tentec-bounces@contesting.com]On Behalf Of Barbara
> Maloney
> Sent: Wednesday, January 07, 2004 1:22 AM
> To: ten tec list
> Subject: [TenTec] Omni 6+ Input vs Output power?
>
> Is it common for the DC input amps, or Ic, to vary from 15 to
22+
> to obtain 100 watts output into 50 ohms when changing bands?
>
> With my Omni 6, I was not able to get 100W output on 3 bands
> before my former 962 supply would trip off at 20A. Have since
> replaced it with a beefier more stable supply with an accurate
dc
> ammeter. The Ic scale runs approx. 1-2 A higher than the
supply
> dc.
>
> Has anyone had a problem running CW at over 20A DC input with
the
> Omni 6? The bands where the efficiency goes to pot (Idc
exceeds
> 20A for 100W rf out) are 160, 30, and 15. I know this agrees
> with at least one other Omni 6 user. Any more?
>
> Thanks &
> 73, Mike, AC5P
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|